Jump to content
SAU Community

Recommended Posts

Hey all :)

I have a problem with my skyline. Only occasionally I will start it and begin to drive.. then when I'm accelerating it seems to lose power and slightly "bunny hop" the bunny hops are not aggressive. it just doesn't seem to be able to get to higher revs. It does happen when it's cold but by the time it's warmed up it still has the problem.as I said it only does it every now and again. Does anyone have any idea what could be wrong?

Link to comment
https://www.sau.com.au/forums/topic/428944-intermittent-problem-with-r32-gtst/
Share on other sites

No mods except for a coke can in the blow off valve (bought like that) :P

Don't know the service history from previous owner. Has had a complete full service. Was happening before I recently got it serviced.. mechanic changed the fuel filter and spark plugs (thinking they were the cause) but problem still persists

It happens at any revs. It happens whenever I accelerate

  • 1 year later...

Found this thread and am bumping it because I have a similar problem. I'll describe it in more detail though.

This happens occasionally, and only early in any drive if it does. Not like right out of my garage but 1 or 2 minutes in. I will probably happen at a frequency of about once every 3 times i drive the car.

Once it happens it will happen until i let it sit out of boost for a while and it will be ok. I even did 5 runs at autocross after this, problem did not crop up.

How violent it is depends on how much throttle i'm using. If I hold it down as i'm trying to accelerate and not let it if it reminds me as if someone who is just learning to driving a manual is driving the car. Off-boost it doesn't do this. It only does it at RPMs in which the turbo is building or holding pressure.

Same recommendations? I don't have another AFM to try otherwise I would but I could install my powerfc and put in a Z32 AFM.

I had an r32 gtst back in 2004 which would do that, the car would lurch back and forth violently under acceleration. Turned out to be a really dirty fuel filter, wasn't allowing sufficient fuel to the rail so the car was suffering fuel starvation. Upon reflection I'm surprised I didn't destroy the engine, must have been running ultra lean during those periods.

I had an r32 gtst back in 2004 which would do that, the car would lurch back and forth violently under acceleration. Turned out to be a really dirty fuel filter, wasn't allowing sufficient fuel to the rail so the car was suffering fuel starvation. Upon reflection I'm surprised I didn't destroy the engine, must have been running ultra lean during those periods.

Did it do this all the time or only occasionally like it's doing for me?

I would think if it were a fuel filter it wouldn't just stop and be fine for hours.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, you are right. It seems easier and more reasonable to boost the engine. And as you said the blocks are very similar but the cylinder bores are different.
    • Sound logic, but in actuality way more illegal than just having the wrong pipe. Normally, doing something like that would be forgery. Meaning you may have certain documentation for vehicle parts, but the actual parts are different ones and you just assign them the numbers and badging from the documents. But nevermind that. Nonetheless, I AM curious if this pipe was ever made by any official manufacturer this way, because I honestly am not familiar with this pipe layout and shape. As I will be putting on the HKS Silent Hi Power once my exhaust gaskets arrive, as long as it sounds right I will just roll with this front pipe. I can always order the actual Mines part if I run into legal issues. It would be an unnecessary expense as there is lots of other problems I have on this car as of now.
    • So, weld a plate with the Mines logo laser cut into it, onto it. Instant Mines pipes, whether they were or weren't originally.
    • I don't know if the blocks are "the same". They will be very very similar. Obviously, either the bore or the stroke is going to be bigger on the 20. If the bore is bigger, then the 18 head is unlikely to fit properly. If the bore is the same, then you can almost certainly fit the CA18 head, but there migth be a few fun things you have to do to make water galleries (or other things) line up properly. Or... it could just be real easy. Is it worth the effort? Almost certainly not. You can make nearly as much power on a 2 valv ehead as you can on a 4 valve. There's not any "magic" in a 4 valve head.
    • Yes, me too!!!!  I need to find a something that has all the abbreviations for what these cars have LOL
×
×
  • Create New...