Jump to content
SAU Community

Recommended Posts

really need some help with this one guys.
I've been reading about and scouring the net for solutions but i cant seem to find anything that's fixed it yet.

Ive got an autech stagea (260 RS)
and whats happening is ill be driving along all good, and sometimes randomly, but usually after ive been coasting in gear for a bit then go to accelerate there will be either no response from the throttle of it will try to rev up and start sputtering like crazy and blowing out black smoke for about 2-3 seconds after which it will come back and run fine for the next few minutes till it happens again for 2- 3 seconds then runs fine straight after. Odd.

so far few things I've tried based on what I've found on the forums from similar problems are:
new fuel pump, replaced fuel reg, replaced CAS, replaced ignition pack, new splitfire coil packs + changed spark plugs as well as plugging in a consult cable to check for fault codes, there were none

I'm really running out of ideas here guys the car other wise runs fine and isn't down on power at all so im really just scratching my head over this one :/

one other thing i should add is today i pulled off the BOV's because i noticed just last week that i was getting a bit of fluttering, if say i put my foot down to full throttle (WOT) then back off to about half throttle it would flutter. (not sure if thats related to the sputtering at all)
I pulled them off and set them up for a bench test, and under 20 psi i was getting a lot of leakage out of the recirc outlet on both valves, within about 3 or 4 seconds the pressure in the piping dropped right to zero

checked everywhere else and there were no other leaks from anywhere else.... surely that's not right?


Link to comment
https://www.sau.com.au/forums/topic/429312-help-rb26-keeps-sputtering/
Share on other sites

ohh yea sorry forgot to add that as well

first i tried re soldering the connector pins to the PCB (a common problem there of having dry joints) which made no difference
so then i bought another pair to try and nothing...no difference

sounds like a good idea but wouldn't blocking them cause the car to stall every time i pull up, blocking them wont cause any other running problems than that will it??

fuel economy is as per normal but in regards to over fueling the only sign of running rich is the black smoke clouds i get when it sputters and some extra blackened spark plugs.

causes for over fueling?..... bad injectors maybe?


will have a shot at running around with them blocked though and see what happens
cheers.

BOVs need positive pressure in the signal port, the 6mm hose off the top, to remain closed and the. When that drops or goes to vacuum the valve opens

Fluttering as you described is normal for a GTR, both mine do it

Give it a full service, all fluids and filters, it's hard to guess the problem over the Internet

BOVs need positive pressure in the signal port, the 6mm hose off the top, to remain closed and the. When that drops or goes to vacuum the valve opens

Fluttering as you described is normal for a GTR, both mine do it

Give it a full service, all fluids and filters, it's hard to guess the problem over the Internet

yea i understand the concept of how they operate...just seemed odd that it was fluttering to me but if you reckon its normal then sweet...bit of peace of mind there, also seemed odd that when i set it up for a bench test with 20 PSI on both sides it was leaaking air out of the recirc outlet pretty quickly. went from 20 psi to 0 in about 4 seconds when i pulled stopped supplying air.

however....

update on the car.....seems to be sweet now

after i cleaned up the BOV's and absolutely drowned them in WD-40 it was still sputtering but after driving around for maybe 40 minutes it seemed to go away

been running fine for two days now cant believe it was as simple as that -_-

Well it turned out to be the bovs either not closing all the way or maybe the plunger not being able to move freely enough

literally all I did was take them out and hit them with some wd-40 and so far so good, will probably look into replacing them still though

hope that helps anyone else with any similar issues

yea i understand the concept of how they operate...just seemed odd that it was fluttering to me but if you reckon its normal then sweet...bit of peace of mind there, also seemed odd that when i set it up for a bench test with 20 PSI on both sides it was leaking air out of the recirc outlet pretty quickly. went from 20 psi to 0 in about 4 seconds when i pulled stopped supplying air.

however....

update on the car.....seems to be sweet now

after i cleaned up the BOV's and absolutely drowned them in WD-40 it was still sputtering but after driving around for maybe 40 minutes it seemed to go away

been running fine for two days now cant believe it was as simple as that -_-

I wasn't sure if that was how you did it as it wasn't stated and that isn't right they should hold that fine

if i get it right i can make them flutter for about 10 seconds, something i do when i'm bored driving around

good to see it's sorted, on to enjoying it

your not in western sydney area by chance, i saw a nice white 260 parked at the shops where we get coffees

yea exactly what i thought defiantly not meant to be doing that, ahh well ill pick up a pair of aftermarket replacements sometime next week just for the peace of mind that it wont come back, but do i really need to buy two, surely i cant just fit one and block the other off ?

hahaha i do the same thing about 10 seconds sometimes if im traveling up hill :thumbsup:
seems to be holding boost much better now than it used to though by the way

nah no where near man im from down in Melbourne, they're starting to pop up more commonly around here now though but everytime i see one its like.... http://i.qkme.me/3paixf.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Latest round of updates on the car. I purchased and installed a SWS clutch slipper to help with 60ft times and got some second-hand good condition 275/40R17 Hoosier DR2 radials. Test and tune in November showed the tyres were an upgrade over my over 15 year old mickey Thompson's and I got a 1.8 second 60ft and pb et of 11.71 but even then, that run wasn't great due to rain and driver error (the event got called off 10 minutes later fast forward to the weekend just gone 25th of Jan and there was finally a break in the weather to let racing happen. The first run the track was slippery and only managed a 12.1@129 Second run the track was better and got a new pb et and mph: 11.54@131   Lith and I then worked out that I installed the previously mentioned clutch slipper incorrectly and its never been working, and I had just been dumping the clutch the entire time, we also noticed it was on street boost and not race boost. So I lined up for a third run with the car turned up in the first two gears, but the passengers side axle objected to clutch dumps and left the chat which stopped my weekend.   so there will be another attempt in the future once I replace the tyres as they rubbed and are stuffed now. but a low 11 should be on the cards.
    • Ceramic coating and heat shielding, you mean?
    • Turbos don't require pulling the motor apart so that's "easier". I would recommend the Nismo R3 turbos instead if you want to do stock twin turbo. It doesn't make as much power as the 2530s but it's only like ~50 whp off the mark and should have better response (ball bearing CHRA, slightly smaller turbo). A local that went with a Garrett G30 and 6boost manifold recently nearly burned his car to the ground after the hood insulator started melting and and burning so if you go single turbo I recommend doing a lot of research and validation work to make sure you don't do the same.
    • New rear lights, filler panel sprayed, cleaned and back together    before, during, after shots 😍
    • 100% is gyprock, I agree. Slip of the keyboard. Haha! I left my indicator bulbs out to save a bit of weight.
×
×
  • Create New...