Jump to content
SAU Community

Recommended Posts

Hi guys, I'm looking at getting paint protection done on my car and have heard several good things about it such as keeping the paint losing like new for 5-8 years, looking like it's been waxed weekly, easier to clean dirt off and that it protects the paint from UV damages.

Is all this true, where to get it done in VIC and roughly how much for the whole car?

I'm totally new to this so any help would be great.

Cheers

Kevin

From a dealership, most are overpriced and definitely not worth the warranty it written on.

12 months to 2 years would be the most you could get out of product and it would have to be Ceramic or Urethane based.

  • 4 weeks later...

Its a wank.

my mate had a detailing business and use to apply this so called paint protection to brand new cars for the dealerships. All he done was give ghe car a full hand polish with a good quality polish. I also have many mates that are spray painters who have also said all it is is a polish and these dealerships charge as much as 3k for this so called paint protection. Be weary my friends.

Josh

Epic waste of your money.

You would be better off putting some money aside for a professional detail, and some time with the detailer to learn how to take care of, and maintain the finish.

Thanks for all the replies guys. I have also been asking around and do some research, it appears a regular wash / polish and occasional detailing is better or just as food as paint protection only lasts a while and it's expensive as.

  • 3 months later...

Final Inspection do a similar thing and you pay per coat I think. Dont know anyone who has had it for more than a few months so, so not sure of results.

should pay more attention to this section...

Final Inspection, FMJ (Full Metal Jacket) 2.5 years and it's starting to get a little tired but still beads and sheets, just not as well as it use to.

I layered another 1-2 layers of FI Seal 'Strong' after FMJ - garaged car, maintained with pH neutral shampoo.

Paint protection from someone who knows what they're doing (ie a proper detailer) can provide long term protection - but you need to be good with your maintenance as well to get the most out of it

Im not going to knock the product Dan, but how many kms have you actually done in those 2.5 yrs....how much time has it spent out in the elements?

Any coating will last years if the car is locked in a garage most of the time....

I've got FMJ on my daily and my mum's car.

most synthetic sealant should last min 6+months

I had it on my car for 2 years it still beads and sheets not as good as when i first got it of course, but its all in the maintenance

with proper maintenance (pH neutral shampoo and some sort of booster) it should last a fair wall.

DON'T ever get it from the dealer complete rip on

personally... a genuine good quality 2K paint job with 2K clear coat is sufficient. my car was parked outside under the elements everyday.... covered with tree sap and bird poo for 2-3 weeks straight. all it needed was a good wash with normal car shampoo and it looked new again. clear coat surface was smooth to the touch as well.

  • 3 weeks later...

We sell paint protection products at the fleet company that i work for, and essentially it's a warranty item - it doesn't do much for the paint on your car, but if you happen to get rust/bird crap/UV damage within a certain period (5 years?) that ruins your paint, then the product manufacturer will repair it- usually with a resprays

I have no experience in this stuff but my father used this guy www.reflection-perfection.com.au on his ve commodore a year and a half ago. My car is getting detailed by him on Wednesday. He is putting a product called Cquartz Finest on my car as paint protection after he has finished fixing up my 1000 swirls lol.

Now, what I will say is that my fathers car still looks fabulous after his detail and, beads like crazy to this day when it rains or when he washes it so I think there is some merit in paint protection. There better be anyway before I fork out my hard earned!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...