Jump to content
SAU Community

Recommended Posts

Hey all,

Need to clear out some room from the shed and need these parts gone as I no longer need them. All parts were removed in working order and were replaced only by new parts for the new set up of the cars. The list is below and will add photos later but you can PM me on here or sms me on 0400262578 for pics. Will try to upload pics as soon as possible.

33 GTSt Stuff

1. rear stock lower control arms $80 the pair

2. rear stock camber arms $40 the pair

3. rear stock traction rods $40 the pair

4. HICAS 4 wheel steering unit + tie rods $100

5. complete front and rear calipers and rotors only (no hubs or knuckles) $300

6. Diff centre minus ring gear $200

7. a/c condenser unit and all under bonnet lines to firewall $100

8. washer bottle and both motors $30

9. TRUST pod filter with green label air flow meter $80

10. clutchless fan $30

11. BLITZ blow off valve (rare) $100

12. turbo induction piping $10 each

13. fuel tank and fuel pump assay $150

14. cat back exhaust and kakimoto cannon (mild steel) $100

15. front castor rods $100 the pair

16. front LCA's $100 the pair

17. front camber arms $40 the pair

18. front traction rods $40 the pair

19. RB25 gears set and selectors + main shafts $400

20. generic 12' thermo fan $80

33 GTR stuff

1. crank scraper (2 piece) $40

2. rear main crank seal $20

3. power steering pump bracket $20

4. stock water pump (no cavitation) $30

5. exhaust manifolds with heat shields $40 the pair

6. oil and water turbo lines $5 each

7. various water and vac lines $5-$15

8. air ballast chamber $30

9. O2 sensors $5 each

10. stock valve springs and retainers $100

Any more stuff I find in my travels I will add at a later date!

Cheers HULI

also have an air regulator for RB26

(the bit that sits under the intake plenum)

Also have the centre grille for a S1 GTSt

(mint condition and in 2PAK silver)

7. a/c condenser unit and all under bonnet lines to firewall $100


8. washer bottle and both motors $30



how much to post this to canberra? does the air con stuff come with the compressor?

For all those people asking the front rotors measure 29.5mm in width and the rears measure 19mm in width. these come with the front and rear disk callipers and brake pads. so slap it on and go!!!!

Still got the O2 sensors and in very good condition!

If anyone needs better photos or something let me know and I can put them up on here or msg me and I'll send you a MMS. My number is 0400262578

Cheers HULI

PS would rather have pick up for exhaust system.

Also if you need some parts and not others I am willing to separate if need be!

If you want quality used stock parts and don't like the price, then shoot me a pm or msg with your offer and we'll go from there. All postage paid by buyer tho!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I am being real ocd and do not want to make amy mistakes so appreciate all help provided. I am overly cautious so asking for opinion even if i know the answer   few questions,   1.re tensioner, should spring be greased lightly?    2.tensioner has two washers , one pressure washer and other has recessed/ seat. I am going to put the recessed one facing tensioner where edges are cut out and pressure washer on top   3. my car has custom triger kit sold few years ago by guy who initially built the engine. I moved the crank gear and it moved in and out easy, only way to remove belt is to slide the crankshaft gear forward which I did. I have seen these being very tough to move , anything to do with my woodruff key?   it has a crank sensor shown in purple which I assume reads from the 12 teeth position mounted to the crankcase gear   4. timing belt doesn’t have arrow stating front or back just a arrow which I think is direction of rotation . Do you agree?   5.i figured out why my crankcase cover was worn as there was no washer installed over the crankcase cover before the harmonic balancer was put in place. It is missing, anyone knows the part number? It looks like this https://justjap.com/products/genuine-nissan-crankshaft-timing-gear-rear-plate-washer-nissan-s13-ca18-a31-r32-rb20-r33-r34-c33-c34-c35-rb25?currency=USD   https://tinypic.host/image/IMG-4535.382Zy2 https://tinypic.host/image/IMG-4537.382dSz https://tinypic.host/image/IMG-4534.382q4U  
    • CTIS (Central Tire Inflation System) has existed since the 80's. I'm looking into buying a Hummer H1 and they generally included it. 
    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
×
×
  • Create New...