Jump to content
SAU Community

Recommended Posts

Hey guys just looking for some advice from you guys who have more experience in these vehicles than I do.

I have a budget of about 4k to spend on my vehicle but want to spend it wisely and with the most reputable people as in workshops, tuners etc.

Car is: r34 gtt sedan manual

3"exhaust turbo to rear

Rfmic

Bc coilovers

Split fires

About to install walbro pump

K&n panel filter

Any help, links or suggested contacts would be awesome. Don't know if to get nistune board or power fc.

Regards,

Rob

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/
Share on other sites

For a $4000 budget and your current mods, I'd be getting an ECU, Highflow R34 Turbo, Z32 Air Flow Meter and a Tune should bring you to about 250-260rwkw.

ECU and Tune only will be about $900 - $1000 and you might get 180-190rwkw or so?

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/#findComment-6954263
Share on other sites

For a $4000 budget and your current mods, I'd be getting an ECU, Highflow R34 Turbo, Z32 Air Flow Meter and a Tune should bring you to about 250-260rwkw.

ECU and Tune only will be about $900 - $1000 and you might get 180-190rwkw or so?

i

Ok so ill order a z32 Afm now... What turbos do u suggest? Also what ecu?

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/#findComment-6954272
Share on other sites

Remember that you'll need the Plug for the Z32 as well, so it can wire straight up.

I've got a 33 and put an R34 Highflow Turbo on it... If you send off your current turbo to Stao from Hypergear he can highflow it for you, changes all the internals of it to steel wheels etc which can support a lot more boost than the standard one, and machines out the housing so it flows a lot more air.

I run a PowerFC with a hand controller, cost me about $1k, plus $500 or so for the initial base tune then a power tune... retunes afterwards are charged per hour.. so only end up being $150-200 or so for little changes.
Nistune is a daughterboard which connects into your existing ECU, its cheaper and retains the standard ecu which is good in some ways... as mentioned above, you can get one supplied, fitted and tuned for under a grand.

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/#findComment-6954294
Share on other sites

Remember that you'll need the Plug for the Z32 as well, so it can wire straight up.

I've got a 33 and put an R34 Highflow Turbo on it... If you send off your current turbo to Stao from Hypergear he can highflow it for you, changes all the internals of it to steel wheels etc which can support a lot more boost than the standard one, and machines out the housing so it flows a lot more air.

I run a PowerFC with a hand controller, cost me about $1k, plus $500 or so for the initial base tune then a power tune... retunes afterwards are charged per hour.. so only end up being $150-200 or so for little changes.

Nistune is a daughterboard which connects into your existing ECU, its cheaper and retains the standard ecu which is good in some ways... as mentioned above, you can get one supplied, fitted and tuned for under a grand.

Ok so what is better though cuz I'm searching all over this forum I can't find any answers, power fc or nistune? And thank you heaps for ur info mate

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/#findComment-6954317
Share on other sites

Chequered Tuning - 110%

How often/much do you drive your car.

I'd seriously consider getting a Hypergear turbo as well.

As for ECU's, i think Trent would pick the Nistune over the FC for a GT-T - but i'd be seriously looking at the offerings from Link/Vipec/Haltech as well. Not up-to-date about who offers what for the GT-T. Best to check this with Trent.

If you went with a newer ECU, you'd be running MAP sensor, so don't need a Z32 - but will if running Nistune and a bigger turbo.

Add some whiteline adjustable swaybars into your budget as well.

You'll need some injectors too. What Walbro you get?

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/#findComment-6954329
Share on other sites

Chequered Tuning - 110%

How often/much do you drive your car.

I'd seriously consider getting a Hypergear turbo as well.

As for ECU's, i think Trent would pick the Nistune over the FC for a GT-T - but i'd be seriously looking at the offerings from Link/Vipec/Haltech as well. Not up-to-date about who offers what for the GT-T. Best to check this with Trent.

If you went with a newer ECU, you'd be running MAP sensor, so don't need a Z32 - but will if running Nistune and a bigger turbo.

Add some whiteline adjustable swaybars into your budget as well.

You'll need some injectors too. What Walbro you get?

Who is chequered tuning....? Never heard of them. Walbro 255lph intank.

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/#findComment-6954332
Share on other sites

Who is chequered tuning....? Never heard of them. Walbro 255lph intank.

Trent and Cat run Chequered Tuning, they're damn good at what they do. They're located in Keysborough and really know their stuff. Sometimes their a little hard to get a hold of, but leave a message with Cat and she'll get back to you.

http://www.chequeredtuning.com/

Best to talk to Trent first about your budget and goals, I'd hold off on getting that Z32 for now, SS8_Gohan is right, you might be better off running a MAP (Mass Air Pressure) sensor instead of a MAF (Mass Air Flow)

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/#findComment-6954637
Share on other sites

May b on the weekends so prob lucky to do half a tank of fuel a month may be a bit more in summer

good answer

E85 time!! :D

You could go flex fuel for not much more, would fit in your budget. Or just full time E85 considering how much you drive it.

Madness not too.

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/#findComment-6954874
Share on other sites

good answer

E85 time!! :D

You could go flex fuel for not much more, would fit in your budget. Or just full time E85 considering how much you drive it.

Madness not too.

Lol u have my attention... Please go on, who's the best to go and see about this

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/#findComment-6954877
Share on other sites

Trent's the best to go to see for tuning... anything, unless it's a wolf :D

Go to unitedpetroleum.com.au or unitedpetrol.com.au - search for just 'E85' and see how the locations of those servos work for you.

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/#findComment-6955317
Share on other sites

Hey guys

Don't really no if this is on the same topic or not but

just wanted to no if anyone on here has had any trouble

with a R34 sedan doors not all locking, when unlocking/locking

it up ?

If anyone one knows what could be the problem please PM me or email me.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/429677-need-advice-r34/#findComment-6964562
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After drying a few days, time to put her back together 
    • The hot exhaust light will come on not from just the cat being blocked, but it's just a temp sensor, and it's designed to warn you to not do things like park in long grass.   If you've been pushing the motor a bit, it can cause the light to come on.   Second if the cat is rattling, I'd suspect it's not blocked, but instead falling apart inside.   The easiest "fix" until you can get a cat put back in, is to unbolt your one, bash the rest of the insides out, and then bolt it back in.   For a daily driver/street car, I am in agreeance of put a cat in the car. If it were race car I wouldn't care if it were removed.
    • No worries at all 🫡 I think the most satisfying things to make are the little bits that are just impossible to find or they're no longer manufactured. Generally I always try to replace parts with OEM wherever possible. This little project is also great because it'll never see the light of day, but strengthen these brackets so it's not just relying on the little standard screws in the headlight plastic. As soon as I saw the standard brackets and screws I thought, "well I'm not going to install with just the screws, the plastic tabs will just snap off". It's crazy how expensive everything has become yeah. But I suppose that's supply and demand; granted it's a lot easier to get brand new genuine parts these days which is fantastic 😊, I don't have to get totally reamed at the local Nissan dealer ha ha We sure are lucky we have all these manufacturers making parts these days, a few really great Australian companies too like Platinum Racing Products and Fit Mint Automotive, what a time to be alive ❤️ . I've got my eye on the RB26 head by PRP as mine has a very fine hairline crack, so that'll need to be addressed some time in the future. If you have any requests or odd things to make feel free to let me know and I can have a crack at making replacement parts ✌️
    • Thanks for sharing this, and BTW if your headlights are in good condition they are worth thousands....you might want to consider replacing them with brand new LED ones like this (https://www.nengun.com/78works/full-led-headlights-r32-skyline) and making enough profit to buy a house in Sydney
×
×
  • Create New...