Jump to content
SAU Community

Recommended Posts

This must be with the Motec system and a stand alone fuel management system?

t4 turbo dominic, direct port nitrous injection

saw a 20 dyno plot making 370kw, it's gonna need 100,000 clutch kicks to rip a skid too

It can be done, it just depends on how much of the RB20 you want use

If want want the use 20 piston rods crank block and head then no your shit outta luck

But if your happy to swap them for say 30 block crank pistons and rods and a 26 head then yeah 1100 hp from a RB20 is easy done

Thanks, I was thinking everything forged and rev over 10K

OP, have you considered swapping to an RB25/RB26?

These are better.

Why not swap to an RB25/RB26?

RB25/RB26 would be better at these power levels. I think you should do it. I hope I was able to suggest this to you before you went ahead with the RB20, because RB25/RB26 are better. At these power levels.

Or buy an R32 GTR.

Read reaction #0 No BS.

In all seriousness we are talking 1000hp... I believe that to be a power figure that requires an experienced engine builder to produce an engine. That being said I also do not think it matters what modern engine you start with... To get it to 1000hp would probably be a similar amount of work regardless.

Therefore OP should take his RB20 to an experienced engine builder and ask them to produce a 1000hp engine capable of over 10,000rpm. Then OP will simply need the manifolds and a turbo to suit.

$100,000.00 later and it will rip good skids.

So all parts rebuild even the sleeves?

I am looking at 50,000$ AUD for this build. I guess Aussie is more expensive than here?

What will I need. I guess

all cnc engine parts

huge turbo,

2000cc injectors

5 fuel pumps

swirl pot

Fuel pressure reg.

R34 GTR gearbox.

Strengthened driveshafts

sticky tyres

ECU

Knock amp

-------------------------------------------

On all replies:

Please no BS again this is serious.

Edited by JDM_R32_R35

Thanks, I was thinking everything forged and rev over 10K

Read reaction #0 No BS.

So all parts rebuild even the sleeves?

I am looking at 50,000$ AUD for this build. I guess Aussie is more expensive than here?

What will I need. I guess

all cnc engine parts

huge turbo,

2000cc injectors

5 fuel pumps

swirl pot

Fuel pressure reg.

R34 GTR gearbox.

Strengthened driveshafts

sticky tyres

ECU

Knock amp

Please no BS again this is serious.

Better make it 7 fuel pumps. Just to be safe. Maybe 8. You can never have too many fuel pumps. If you run enough fuel pumps, you won't need the fuel pressure reg. They'll regulate each other. Like a team.

  • Like 1

Better make it 7 fuel pumps. Just to be safe. Maybe 8. You can never have too many fuel pumps. If you run enough fuel pumps, you won't need the fuel pressure reg. They'll regulate each other. Like a team.

Thanks again. I thought this was a nice forum to ask about tech. info on skylines but, as usual the jealousy,hate as always.

If you are pushing this much power, I'd suggest making sure your panel gaps are exactly factory spec. Talk to this guy, he can help. Can't recommend him enough for gap talk

f*kcing benji.

I suggest you look in here for some inspiration.

http://forums.bimmerforums.com/forum/showthread.php?1575817-An-Example-of-Truly-Impressive-Turbo-Engineering

$50k might get you the crank....?

You'll need a more sizeable budget to achieve your very rigid specific goal.

Ask them for a quote, prepare by sitting down.

  • Like 1

Thanks again. I thought this was a nice forum to ask about tech. info on skylines but, as usual the jealousy,hate as always.

This is a nice forum to ask about tech...

In terms of your request, it is an unknown and defies logic on many levels, hence your replies.

We do get a lot of entertaining ideas but a lot are from school kids with nothing better to do, in this case you asked a question and got many answers! None of which are useful but we hope you enjoyed your stay and got some entertainment from it!

Thanks again. I thought this was a nice forum to ask about tech. info on skylines but, as usual the jealousy,hate as always.

No no no no, you're mistaking us with Nissansilvia.com. This is a HORRIBLE place to ask questions about Skylines. Awesome place to SEARCH and RESEARCH though...

I suggest you look in here for some inspiration.

http://forums.bimmerforums.com/forum/showthread.php?1575817-An-Example-of-Truly-Impressive-Turbo-Engineering

$50k might get you the crank....?

You'll need a more sizeable budget to achieve your very rigid specific goal.

Ask them for a quote, prepare by sitting down.B

Been quoted already at the cnc shop for these and they said 30K Euro for all this spec.

100K is a bit crazy because that would a 1000hp R35 GTR go here for all the parts.

Anyway different country diffrent pricing.

Been quoted already at the cnc shop for these and they said 30K Euro for all this spec.

100K is a bit crazy because that would a 1000hp R35 GTR go here for all the parts.

Anyway different country diffrent pricing.

What are you trying to achieve? I mean as in WHY are you spending so much on the 2L engine?

This is a nice forum to ask about tech...

In terms of your request, it is an unknown and defies logic on many levels, hence your replies.

We do get a lot of entertaining ideas but a lot are from school kids with nothing better to do, in this case you asked a question and got many answers! None of which are useful but we hope you enjoyed your stay and got some entertainment from it!

O.o seems here also a lot of school kids and dreamers lol. As usual.

No no no no, you're mistaking us with Nissansilvia.com. This is a HORRIBLE place to ask questions about Skylines. Awesome place to SEARCH and RESEARCH though...

Thanks both.

What are you trying to achieve? I mean as in WHY are you spending so much on the 2L engine?

Highest hp on a rb20det. Builder agreed with me that I need all cnc parts.

O.o seems here also a lot of school kids and dreamers lol. As usual.

Hmmm maybe people with more realistic goals... How did you pull the 800kw figure out?

Hmmm maybe people with more realistic goals... How did you pull the 800kw figure out?

1000hp right?

I have seen some 800hp rb20det already around.

Been quoted already at the cnc shop for these and they said 30K Euro for all this spec.

100K is a bit crazy because that would a 1000hp R35 GTR go here for all the parts.

Anyway different country diffrent pricing.

e30K is $44k aus.

now calculate redability of parts, shipping costs, real currency value you are pushing it to the very least $120k AUD.

labour

tax

aussie car dream boats who over charge on EVERYTHING

now, we are in the $200k AUD mark already.

1000hp right?

I have seen some 800hp rb20det already around.

Fair enough! If you manage to do it then post a build thread so we can all admire and STFU :P

I know if you do manage to pull it off ill be the first to say congrats!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ok so I have sorted everything with my uniclutch and  i can offer up a bit of feedback and some things that might help others.    I found problems with factory damper line. Weird shit and had trouble with peddle adjustment    I used this https://au.gktech.com/products/r33-gts-t-skyline-braided-clutch-line?_pos=2&_sid=22b01b9b9&_ss=r Also when adjusting peddle leave a bit of play. You can get into a over stroke condition easy.. Make sure you can push the slave forward after adjusting to confirm fluid can return to master then you will need to pump it up heaps…..not sure why but that’s how it is.    last thing the splined adapter is machined perfectly. If your input shaft is old like mine was I would put a bit of valve grinding paste on it and stroke it like a 15 year old. Just to give it a tad more clearance and to better match it to the spline.    reason is on a near flat shift I have had situation where the peddle returns a millisecond after you lift from the clutch. No slip or anything but I reckon this is due to tolerance on the spline being way tighter than stock clutch and binding for a sec. I think this will go away but also my spline was old. Box is old so I guess I should have checked better. It’s a super neat fit.    it feels light as and holds awesome without any noise    
    • My Fuga Hybrid is JDM, 2014 model but very similar to the V37 from the looks of things..same platform just physically larger and very comfortab;e
    • Was that Australia Delivered Duncan? Does it have siren etc?   I used to have remote start on an old 32 two decades ago, it was a cool feature. I used to wake up early in winter for work. Start it and by the time i was out the door a few minutes later the engine was warmed up and the heaters had the car toasty. It was great.    I don’t mine the ambience lighting.  I drive a western star and it has footwell lights and ambient lighting and it’s great! From the pics of seen of them installed in a skyline I think it’s a nice touch 
    • re the security system, my Fuga/Q70 has the factory option where the puddle lights in the mirrors turn on when the prox key is detected, it was clearly dealer fitted and has a switch in the lower dash to disable it....it didn't have remote start but TBH I don't really miss that, I had it in the Stagea originally but never used it....we don't often have to warm the car up in the snow before we get in for Australia. And the Fuga also has the illuminated footwells, sounds like a useless feature but I actually quite like the indirect light within the car, it was a nice addition
    • Ok now I’m extremely jealous 
×
×
  • Create New...