Jump to content
SAU Community

Recommended Posts

I'm in the middle of a decision point with my project and I'm stuck between two choices.

Firstly, I'm using an RB20DE Neo head, but we'll argue that point later.

It has the same valve train as the rb25 neo heads, which is the same solid lifters with shim over bucket (biscuit type), and I'll be running single coil springs with a seat pressure of 75lbs and 160lbs nose assuming 10mm lift or so.

My first option is the easiest, and that is to run the original biscuit shims and chuck in a set of RB26 aftermarket cams. My main concern is if the shims being spat out and I want to see if anybody has had any experience with the neo engines at high RPM, say 8000-9000rpm. I've never had any problems with biscuits on the european tin I work on (ferrari/jag classic and historics), but tbh they dont get as much of a thraping, even the race cars.

The second option is to convert to shim under bucket (top hat), which was my original plan. Simply because I thought all aftermarket solid lifter cams ran a BCD of 29mm (please remember this is my first foray into RB's) and I've only been looking at RB20/25 aftermarket cams until this point.

I could run the original lifters with 29mm bcd cams if I ran a 1.5mm top hat as a packer shim, but I really dont like the idea of running both top hat and biscuit shims.

To run top hats I would have to run a set of renault clio aftermarket buckets on the exhaust side and a set of supertech KA24DE lifters on the inlet side. I would then need to run approx 1.5mm thick shims on the inlet and 3mm on the exhaust. The inlet wasnt such a problem, but the exhaust shims would only have a 1.5mm skirt depth as the collet sits 2mm below the tip of the valve stem. So a shim with 3mm up top and 1.5mm location below I wasnt so sure about...

This also works out incredibly expensive at over a grand for just valvetrain components, compared to a set of r32 RB26 cams from tomei/kelford etc etc.

So, before I pump for the cheap option, I'd really like to know if any of the big tuners out there have ever run a neo to high outputs/rpm and spat a shim.

I really dont want to spit a shim as I've got a one off engine build with custom head, adaptor plates, custom pistons, custom head gaskets, custom ex manifolds........and a spat shim would destroy that investment and make me cry quite heavily if a rogue valve went exploring around the engine.

But it is over a grand cheaper.

  • 2 years later...

Hi mate just wondering if you ever finished this project as I'm looking to convert my neo rb25 head to shim under bucket using gtr buckets, I haven't done any measuring as such yet to see if it is possible but waking up a old thread to see where you eventually got to.

Thanks, J

  • 5 years later...
On 8/13/2013 at 7:12 PM, BenR said:

I'm in the middle of a decision point with my project and I'm stuck between two choices.

Firstly, I'm using an RB20DE Neo head, but we'll argue that point later.

It has the same valve train as the rb25 neo heads, which is the same solid lifters with shim over bucket (biscuit type), and I'll be running single coil springs with a seat pressure of 75lbs and 160lbs nose assuming 10mm lift or so.

My first option is the easiest, and that is to run the original biscuit shims and chuck in a set of RB26 aftermarket cams. My main concern is if the shims being spat out and I want to see if anybody has had any experience with the neo engines at high RPM, say 8000-9000rpm. I've never had any problems with biscuits on the european tin I work on (ferrari/jag classic and historics), but tbh they dont get as much of a thraping, even the race cars.

The second option is to convert to shim under bucket (top hat), which was my original plan. Simply because I thought all aftermarket solid lifter cams ran a BCD of 29mm (please remember this is my first foray into RB's) and I've only been looking at RB20/25 aftermarket cams until this point.

I could run the original lifters with 29mm bcd cams if I ran a 1.5mm top hat as a packer shim, but I really dont like the idea of running both top hat and biscuit shims.

To run top hats I would have to run a set of renault clio aftermarket buckets on the exhaust side and a set of supertech KA24DE lifters on the inlet side. I would then need to run approx 1.5mm thick shims on the inlet and 3mm on the exhaust. The inlet wasnt such a problem, but the exhaust shims would only have a 1.5mm skirt depth as the collet sits 2mm below the tip of the valve stem. So a shim with 3mm up top and 1.5mm location below I wasnt so sure about...

This also works out incredibly expensive at over a grand for just valvetrain components, compared to a set of r32 RB26 cams from tomei/kelford etc etc.

So, before I pump for the cheap option, I'd really like to know if any of the big tuners out there have ever run a neo to high outputs/rpm and spat a shim.

I really dont want to spit a shim as I've got a one off engine build with custom head, adaptor plates, custom pistons, custom head gaskets, custom ex manifolds........and a spat shim would destroy that investment and make me cry quite heavily if a rogue valve went exploring around the engine.

But it is over a grand cheaper.

Hello Ben, was curious what your findings were with this head project? Mainly curious how using the 20de head worked out. I’ve always been curious how interchangeable these heads were , 25det, 25DE, 20de, 20det, 26, NEO, esc. Obviously the flanges are different and some head stud differences, I believe some coolant passage differences, but as far as castings and flow capability, I’ve been curious how similar they all are 

Neo NA ports are tiny. The 20DE Neo would be a poor choice for a power build. The 25DE Neo is a poor choice for a power build.

The Neo head (turbo more so than the NA) is a good thing, the threat of spat shims notwithstanding. It is hard to quantify how severe that threat is. Not enough datapoints to really tell the story. It seems, though, that most people running sensible sized cams have no problem.

Neo is superior to 26 because of factory VCT, if nothing else. 26 flows more (I think) without any extra work, but that is easily changed in any serious build anyway. Neo combustion chamber is smaller, which is an improvement.

None of this is new knowledge. It has all been posted on here before, over the last 20 years.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update for the sake of closure   Ended up getting the intercooler piping all sorted, new plugs and yellow jacket coils, and she was idling mint until it warmed up while I was bleeding the cooling system. Found the misfire to be localised to cyl 3 by unplugging coilpacks, ran a compression test, that checked out, then decided to get a mate to check if that spark plug was firing out of the motor. Upon cranking it over, with the injectors disconnected, the car actually fired and ran on a couple cylinders and heaps of fuel came out the top of cyl 3 I'd say that injector's either spraying incorrectly or spraying far too much, which is fine as I'm planning on replacing them anyway I'm planning on making about 250kW on flex fuel, and have a set of 1000cc injectors from ozautosport, obviously overkill but I'm planning on building the motor and running more boost further down the line, do you reckon they'd be too big for a smooth idle on 98? Thanks for the replies gents, much appreciated
    • I'm confused. You said you want to "remove the clear coat from most panels" but it sounds like you are actually doing a full respray? Few random things to add -  If you chase the blistered paint with 120 grit, I can almost guarantee you'll chase it down to bare metal (that's fine). But if you paint the car from here, you'll have nice little indents where ever the blistered paint was. The new paint won't magically level out the low areas, you need to fill them. Which leads me to the main point I wanted to add, make sure the whole car is flat before you paint it. All those areas with blistered paint you sanded out, make sure to fill them and triple check they are flat with a block guide coat. I'd also check the whole car is flat with a large block and guide coat but yeah up to you if you want to go that far.   
    • 300hp (225kw) is barely outside the standard turbo's range with a bit of extra boost in it (200ish). If you are going to change the turbo you should aim for 250-300kw (330-400hp) to make the expense worthwhile
    • A couple of things, firstly omg that turbo is expensive! $3,000 USD for dinosaur technology is robbery. You could buy a G series turbo and have a good amount of change instead.  If you want a good budget option, have a look here - https://hypergearturbos.com/product/rb25dethighflow/ If you are keen to spend more, have look at the modern turbos, Garrett G series, Borgwarner EFR, etc. Have a look at the RB25 dyno results thread for inspiration.  If you upgrade your turbo to something that will support the 300hp you want and only "probably" have Haltech ECU, your car will only "probably" run. Actually, no it won't run. You are going to need the ECU and injectors at the time you do the turbo upgrade.  No thoughts on "this much boost" as you didn't say how much boost that actually is. Having said that, plenty of unopened RB25's making even more power then what you are chasing.   
×
×
  • Create New...