Jump to content
SAU Community

Stagea Warning Light

webng

By webng,
in Four Door Family & Wagoneers

 Share

Recommended Posts

webng Experienced

webng

Posted
  • Author
Posted

Well the parking foot brake has been faulty for years (foot pedal will depress but won't release when i pull the lever) now so I don't use it at all. But this is the first time the light has come on. If that's just it I shouldn't worry?

Spong Collaborator

Spong

Posted
Posted

Sounds like the cables have seized up, which I think happens sometimes back when I owned a C34. Could be a problem if the brake pads are pressing on the discs. It's certainly worth jacking it up to see if that's the case. If you were here in NZ, a 6 monthly warrant of fitness check would keep your car off the road if the parking brake failed.

webng Experienced

webng

Posted
  • Author
Posted

Thanks, will check when i get home. Top up and service in a couple of weeks so all good.

Definitely low brake fluid Nick, had the same issue with mine, topped up and it went off. Just check the level, I can almost guarantee you that it'll be on low. You might be due for some new pads as well.

zoomzoom Mentor

zoomzoom

Posted
Posted

http://www.skylinesaustralia.com/forums/topic/424151-sticky-parking-brake/#entry6948181

Well after having the pedal seize right up on me, I thought it was definitely going to be a removal job.

To avoid that, I gave the WD40 treatment another go. This time I had to lay down mats, newspaper and towels to stop the WD from getting onto the carpets. Using a bit of PVC tubing attached the can I was able to soak the pedal mechanism from every angle, completely soaking the area until the WD was running off onto the towels. Repeated a few times.

Well f**k me, it worked a treat. It freed the mechanism right up, the pedal now releases fully when you pull the brake release. My only concern is that I did wash off some grease on the pedal, so hopefully I haven't affected any lubrication points, but if I have to add some oil or grease in future its not too much a big deal.

Will report back if I actually ended up ruining the pedal, but so far so good. Beats having a stationary vehicle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      Ah, fair enough. For the IAT, I'm using a legit GM sensor that was used on the car prior to my current build. I'll get another wideband and IAT ordered and follow up when they show up. Thanks for the help.
    • GTSBoy
      RB20DET lean on cold start

      By GTSBoy · Posted

      You shouldn't need to massively fatten up the mixtures for cold conditions. For one thing - 0°C is not that cold. For another, the Haltech will be using the IAT sensor to tell it how dense the air air, and calculate the correct amount of fuelling. Then the cold start enrichment is added as a % on top of that, so it should scale with the main fuelling. You might also doubt the IAT sensor at this time. You're not using one from an RB26 are you? Using a nice Bosch sensor or similar? Happens. Some wideband units take great pleasure in killing their sensors. Put another wideband in the tailpipe and compare. Or just swap the sensor to a brand new one and see.
    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      Oh, my misunderstand. When the car was running, it sounded ok, but if I gave it any gas it wanted to die but caught itself afterwards. It's very different from how it was a couple months ago when it was warmer outside. The logs show that the AFRs are better during, what I assume, is warmup enrichment. Because it's cold, and air is more dense, should I work on the enrichment bit?
    • A31Skyline
      Rb20e and RB20DET parts

      By A31Skyline · Posted

      yess of course im not using 2nd hand parts from my spare engine, but the place where i live is hard to find parts for the RB20DET ,but for the RB20E is everywhere including new ones and a lot cheaper ,because for the RB20DET you have to order it overseas to get one and it cost a lot of money 3x the price to be exact. so i ask this topic because if i can use the new ones but for RB20E is it compatible or not. if not im screwed haha, not totally screwed but i have to save a lot of money first before i can begin repairing my engine, thanks for the information before.
    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      Unless my sensor just died, was only a couple months old, I strongly believe it didn't. How can I test it? I never mentioned it being 20:1+?
×
×
  • Create New...