Jump to content
SAU Community

Recommended Posts

  • 2 months later...

They're amazing, have tuned several cars with them already and you have very little issue with reversion when you back off the throttle on light load unlike the Z32 where I often recommend placing a few bends in the intake.

I've just ordered the higher reading HPX ones for another 2x cars I'm tuning (both on Nistune). Literally click a drop down and select the R35 AFM and pipe size.

  • Like 1

My R32 just got done tuning with Nistune using R35 AFM as well.  But since I'm running factory size tube (65mm) and the existing VQ map doesn't go below 3", my tuner spent an hour just re-mapping the VQ map.  After he was done he was so impressed with R35 AFM that he ordered new R35 AFM for his personal R32.  

all the tuning is done in the following table so you actually dont really need the data, i've had to make dozens of maf curves from scratch as we mix and match housings and cooler pipe sizes on a weekly basis.

Most people forget that with powerFC the FUEL table is only a target AF table and should not need "TUNING" (Fill in your taget afs in the INJMAP table then tune in the AIR FLOW CURVE table)

image.thumb.png.c55819c23e0ace414c663b4d5e3b1ad6.png

image.thumb.png.40e1cd06a04a5ef44467f57b1234a7c6.png

 

  • Thanks 1
  • 2 weeks later...

 Glad everyone is enjoying the conversion .  I've got mine on the Dyno now being tune and we are having issues with the internal IAT in the 35 MAF messing with the reading on the stock RB 26 IAT sensor. Turning with power FC and voltage jumps out of nowhere

Edited by kunzz
  • 1 year later...
On 10/14/2017 at 1:22 AM, kunzz said:

 Glad everyone is enjoying the conversion .  I've got mine on the Dyno now being tune and we are having issues with the internal IAT in the 35 MAF messing with the reading on the stock RB 26 IAT sensor. Turning with power FC and voltage jumps out of nowhere

How did you go with this mate?

Also have a GTR which is currently stock with a PFC and TBE. Planning to single sooner rather than later, but won't be building the motor for quite a while so am happy to keep it simple with the PFC. A single R35 AFM would make things super simple and dirt cheap while the cars still at a very basic level.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • https://www.youtube.com/watch?v=KyZDvZmvhik
    • You'd be better off digging a pit and standing under it to shoot it.
    • The easiest way would to be ignore the oscilloscope, grab a multimeter, and make sure all the main connections are right. An oscilloscope will give 99.9% of even technicians so much grief, as they have no idea what things should even look like on an oscilloscope. Which is also even more likely for someone who's first ever major work on a car is this If the battery volts are dropping down so low, the LDV will reboot the ECU, when it does so, it will drop out the start circuit. If this is occuring, the battery voltage should also come back up. Give it a few tests, even simple ones like when you're attempting to crank it, measure voltage from the engine block, to the negative terminal. You might find you've got really bad connections somewhere. My guess is the "new" motor has something like a shit starter motor, at which point, you can swap the starter motor from the old motor, to the new motor. Before I did any of the above though, I'd 100% confirm the battery in the vehicle. Most jumper packs are absolutely useless, especially if a battery has a bad cell for example. Also the new modern "jump packs" if you don't know what you're doing with them, you won't even get them into high current stage. So go back to basics, check the battery, especially with a known good one as a replacement test. Check ALL the wiring, this includes where they're bolted onto the battery, and bolted onto the starter motor. Check all the earth straps are on. Measure your resistances across your earth straps. A good check here is to measure voltage across the earth straps while you're trying to crank it. If you're seeing voltage, you've got high resistance joints! Oh, and once you've done the above, check the battery over again.
    • For most rotisseries, as Duncan has mentioned, you really don't want a full car on it, you want a stripped shell. And imagine how many more weeks THAT is going to add to working on the car...
×
×
  • Create New...