Jump to content
SAU Community

Ecu Comparison

FJ RB25

By FJ RB25,
in Engines & Forced Induction

 Share

Recommended Posts

Lithium Grand Master

Lithium

Posted
Posted

Hi everyone and thank you for your advice

I have just finished speaking to a fella over here in Perth who used to work for 101 garage in QLD

Looks like I will probably go with the Haltech unit and the 3073 turbo on top of a 6 boost manifold.

I didn't realize that running E85 was that much of a mess around ( excuse my ignorance)

Will use the AFM to pass licensing and then run the internal MAP sensor in the ecu.

The engine exhaust noise shouldn't be too much of an issue as long as its gone properly.

Most probably won't be pulled over every day like you do in a skyline majority of 5 O wouldn't expect that from an old fj holden

Sounds like a potent setup in the making, look forward to seeing how the HTA3073 goes... Should be very responsive!

Would love to play with Haltech sometime, sounds like they are good products but G4 Link dominate here... For good reasons, but not necessarily that they are the best

Nee-san Grand Master

Nee-san

Posted
Posted

Good points there to consider there, only going by what was recommended to me with the turbo size, thank you for the advice and I will do some more research when I get back to the big smoke, if I can go a smaller turbo and pick up good response then that's great, not after huge HP just some decent HP so the car is fun to drive.

If Fitting the AFM to get past licensing then running the MAP sensor part of the ecu after is what I have to do then I will do that no big deal.

Running E85 was only an option to get past the emissions part of licensing due to the fuel burning cleaner if it was needed, once car is licensed I was going to run premium pump fuel.

Ok so I have a few mates that build Rb's and I have spoken to RIPS over in NZ because I was looking at one of their manifolds at one stage and some fellas that have drift cars.

Recommended so far

Haltech

Wolf

Power FC

Link G4

What about a Vipec man ! ?

Hanaldo Grand Master

Hanaldo

Posted
Posted

Link manufactures the ViPec so its the same ECU essentially.

They're actually not. The Nissan plug in boards are quite different. The VIPEC plug ins have quite a few features that the Link plug ins don't .

kitto Mentor

kitto

Posted
Posted

They're actually not. The Nissan plug in boards are quite different. The VIPEC plug ins have quite a few features that the Link plug ins don't .

Yes true. Built in Knock boards on the ViPec being one of them. Along with a few other small features. But they are a very similar platform. Software is almost identical with few small differences between the two. The ViPec does however support Peak and Hold Injector drivers. But i really don't think that is such a big issue nowadays. There are that many different high impedance injectors on the market at a reasonable cost, there is no real reason that you must require a Peak and Hold Injector capable ECU.

The Link is cheaper. And now with the release of the G4+ the differences are closing up. The G4+ now has built in digital knock control.

I'm sure if you scurried the Link forum you'd find a thread with all the differences between them.

XRATED Veteran

XRATED

Posted
Posted

Hi everyone and thank you for your advice

I have just finished speaking to a fella over here in Perth who used to work for 101 garage in QLD

Looks like I will probably go with the Haltech unit and the 3073 turbo on top of a 6 boost manifold.

I didn't realize that running E85 was that much of a mess around ( excuse my ignorance)

Will use the AFM to pass licensing and then run the internal MAP sensor in the ecu.

The engine exhaust noise shouldn't be too much of an issue as long as its gone properly.

Most probably won't be pulled over every day like you do in a skyline majority of 5 O wouldn't expect that from an old fj holden

Yeah good plan... haltech and 3073 will be a good combo.

After the initial rego and engineering inspections, you would be left alone pretty well. More likely to be pulled for cops to have a look than a ticket.

FJ RB25 Enthusiast

FJ RB25

Posted
  • Author
Posted

Well that's the plan anyway, I do find that being in my early 40s that I rarely get pulled over, probably got something to do with the fact that as you get older its harder for them to BS you.

I feel for all the young fellas out there who go and spend good coin on a nice car only to be goated and harassed by the boys in blue.

Majority of engine builders that I have spoken to recommend the Haltech with either the 3073 or 3076

Thank you everyone for your advice and input

Cheers

Paul

Hanaldo Grand Master

Hanaldo

Posted
Posted (edited)

Yes true. Built in Knock boards on the ViPec being one of them. Along with a few other small features. But they are a very similar platform. Software is almost identical with few small differences between the two. The ViPec does however support Peak and Hold Injector drivers. But i really don't think that is such a big issue nowadays. There are that many different high impedance injectors on the market at a reasonable cost, there is no real reason that you must require a Peak and Hold Injector capable ECU.

The Link is cheaper. And now with the release of the G4+ the differences are closing up. The G4+ now has built in digital knock control.

I'm sure if you scurried the Link forum you'd find a thread with all the differences between them.

Built in knock sensor, on-board MAP sensor, ignition outputs for each cylinder, etc.

Not a lot of differences no, but I do think they make the ViPEC a bit better value than the Link. Especially when you consider that with the Link you need to pay for an IAT sensor as well, and if you want to run any decent boost then you will need to splash out on a MAP sensor which means you also need to buy the XS Loom... Presuming you want to ditch the AFM. Given the ViPEC comes with the IAT sensor and on-board MAP sensor, the initial outlay ends up pretty close. Just food for thought.

Edited by Hanaldo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • marni
      I need more than help to finish my R33

      By marni · Posted

      Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • r32-25t
      Attesa pump mount options / ideas? R32 gtr style.

      By r32-25t · Posted

      From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • GTSBoy
      R34 Manual conversion Speedometer

      By GTSBoy · Posted

      Have you looked at the workshop manual?
    • GTSBoy
      rb25 gearbox mount options - solid mount?

      By GTSBoy · Posted

      Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
    • FRGTN1
      R34 Manual conversion Speedometer

      By FRGTN1 · Posted

      I have a r34 sedan 1999 manual converted need some help with my speedometer it only reads upto 98km and then stops currently still running the auto cluster any easy fixes no speedo drive is connected yet, if someone has a video for wiring up the manual speedo sensor with the auto cluster please send through 
×
×
  • Create New...