Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Morning everyone.

Bunta, thanks for recommending battery doctor. My phone actually lasts during work now although it still had to be plugged up. Apparently it doesn't like charging over USB...

No worries.

Howdy all Ecu dropped at store for modifications for rb25 should be 125 and mines afm plug is ordered going to be taking that to an auto elecy to do

All that is left now is some ball joints, shocks, front mount, highflow, sub frame and diff bushes, clutch and brakes

Already have a stockpile of parts at home and in the car.

Just over 2g left to spend and I'm done :D

Then spending all the kesh on the 25/30!

what power capable high flow?

you will likely need a bigger turbo if you go the 3L, they are very much a GT30 sized unit minimum deal.

This. If your putting a new turbo on your 25 only to latter add it to your 25/30. I reckon it needs to be a GT35 or bigger. As Tits said GT30's are a minimum but to get a decent number from it you should be looking at a 35 or equivalent

Howdy all Ecu dropped at store for modifications for rb25 should be 125 and mines afm plug is ordered going to be taking that to an auto elecy to doAll that is left now is some ball joints, shocks, front mount, highflow, sub frame and diff bushes, clutch and brakesAlready have a stockpile of parts at home and in the car.Just over 2g left to spend and I'm done :DThen spending all the kesh on the 25/30!

sounds exciting Zac ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...