Jump to content
SAU Community

Recommended Posts

hey guys, wondering if anyone has come across this noise before

my na r34 make a whining noise at almost exactly 80km/h in 5th gear at about 1/4 throttle, it sould like i could be comming from the gearbox, cheaked oil levels and all seams fine

if anyone has heard this would love to find out what it is and if there is a fix

cheers

Link to comment
https://www.sau.com.au/forums/topic/432249-r34-whining-at-80kmh/
Share on other sites

probably, how could i cheak that? would it be a lack of diff oil or something messed up internally

If it's only doing the while in one gear (e..g 5th) then you can point at the gearbox. If it's whining in whatever gear at that speed (e.g. drop it to 4th and 3rd) then it's most likely diff. Does it whine under load or all the time (e.g. lifting off going downhill)?

Wheel bearings?

Yeah that was my first though when I saw this thread. I'd say check wheel bearings, though it does sound a bit strange that it's happening in a specific gear - in terms of wheel bearings.

Measure the diff gear backlash and replace shims where necessary. Replace the oil.

Although you could just be low on oil, it's best to do the job properly and check the clearances as the gears and shims wear over time.

The pinion bearings may need replacing also, this is a bit trickier.

ill see if it does it in other gears tomorrow on my way to work

it doesn't sound to much like wheel bearings because when i load them by weaving left to right it isn't any worse

what oil does it take do you know?

epx 80w-90 or multitrax?

I had this problem with my subaru. Eg. Is the same speed. Slower barely hear it. Faster gone. I changed the gearbox and it fixed the problem. Not sure if it was the gears meshing or the pinion gear. Id say that wheel bearings make a whirring noise not wining. Snd pinion gear id guess is the front diff. So I would say possible diff relation or gearbox. Hope this info helped.

Found out today what it was

Got it up on the hoist at work and ran it up to speed

Sound was comming from where the gearbox meats the tail shaft

I'm guessing there's a bush or baring in there that has gone

No noise comming from the box or diff

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
    • Should have taken that opportunity to slot in a twin scroll turbo setup. Maybe next time.
×
×
  • Create New...