Jump to content
SAU Community

Recommended Posts

Hey guys, New to the forum.

Im in the process of buying an r32 gtr and sent out RACV to give the one im keen on a checkover and reported back all sorts of issues.

- Oil leak on front, rear upper engine

- Gearbox oil leak

- Clutch fluid contaminated/ low

- Brake fluid contaminated

- steering rack fluid leak

- Brake hoses perishing/ageing

Do you think these are all due to fair wear and tear, constant abuse or tell tale signs of something bigger?

Seller has stated that he has not done a rebuild of the motor so if I do go ahead with the purchase, is that what im in for?

Thanks for your input and recommendations

Link to comment
https://www.sau.com.au/forums/topic/432257-purchase-r32-recommendation/
Share on other sites

Hi Chris,

It is hard to guess accurately, but generally those points seem to be minor and consistent with a 25 year old car.

- Oil leak on front, rear upper engine. Likely to be a cam cover seal, needs to be cleaned and replaced

- Gearbox oil leak. Unusual to be the gearbox, the engine's rear main seal is more common. This could cost a bit to fix because it will probably require the gearbox to be removed. If its not too bad leave it until the clutch is next replaced when the gearbox has to come out anyway

- Clutch fluid contaminated/ low - very common after 25 years. Probably just needs bleeding, at worst you may also need to replace the slave and/or master cylinder

- Brake fluid contaminated - just need to bleed the fluid

- steering rack fluid leak - some seal or other, or at worst recondition the whole rack

- Brake hoses perishing/ageing - very common. replace them with either rubber or braided ones.

BTW didn't RACV provide an estimate of cost for the repair as part of their report? I'd guess $1-2k to address them all if you are confident to do some of them yourself.

What isn't on that list is rust, smoking engine, rough running engine, bent suspension etc etc, they are all the expensive things!

Hi Chris,

It is hard to guess accurately, but generally those points seem to be minor and consistent with a 25 year old car.

- Oil leak on front, rear upper engine. Likely to be a cam cover seal, needs to be cleaned and replaced

- Gearbox oil leak. Unusual to be the gearbox, the engine's rear main seal is more common. This could cost a bit to fix because it will probably require the gearbox to be removed. If its not too bad leave it until the clutch is next replaced when the gearbox has to come out anyway

- Clutch fluid contaminated/ low - very common after 25 years. Probably just needs bleeding, at worst you may also need to replace the slave and/or master cylinder

- Brake fluid contaminated - just need to bleed the fluid

- steering rack fluid leak - some seal or other, or at worst recondition the whole rack

- Brake hoses perishing/ageing - very common. replace them with either rubber or braided ones.

BTW didn't RACV provide an estimate of cost for the repair as part of their report? I'd guess $1-2k to address them all if you are confident to do some of them yourself.

What isn't on that list is rust, smoking engine, rough running engine, bent suspension etc etc, they are all the expensive things!

Thanks for your reply mate.

Nah no cost estimate for fixing all those things. Just says recommended getting quote to fix before purchasing.

The report said the rear quarter panel may have rust but needs an expert to see it and give a conlusion as the report was inconclusive. Apart from that the tester said the car was good

With the RACV check over, do you just give them a call, tell them where the car is and they sort everything from there?

Yeh give them a call and location, car and theyll send someone out. In the case of this, the guy needed to take it to an assessment Centre to be assessed

  • Like 1

Too true.

I know you're new, but no need to post the same thread in two sections;

http://www.skylinesaustralia.com/forums/topic/432256-buying-r32-gtr-oil-on-motor-issues/

They're tough cars but an R32 GTR being a 25 year old high performance car is bound to have multiple issues unless the previous owner spent big dollars on it before you got it. (and even then) Like the person in the duplicate post has already stated - be ready to sink a few thousand more into it after you get one. Especially if you're planning on driving it hard. No one buys one just to drive to the milk bar and back on Sundays.

As someone on here once said. If you can't afford to buy two GTR's, you can't afford to run one :)
  • Like 2
As someone on here once said. If you can't afford to buy two GTR's, you can't afford to run one :)

That's so true.... :woot::woot: :woot: :woot:

But sometimes it's more like ' if you can't afford two houses, you can't afford one moddified gtr '

  • Like 1

That's so true.... :woot::woot: :woot: :woot:

But sometimes it's more like ' if you can't afford two houses, you can't afford one moddified gtr '

I dont have two houses...... thats why I have a modified GTR hahaha.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jdm DC2R is also nice for a FF car compared to the regular hatches of the time.
    • Now that the break-in period for both clutch and transmission is nearly over I'd like to give some tips before I forget about everything that happened, also for anyone searching up how to do this job in the future: You will need at least 6 ton jack stands at full extension. I would go as far as to say maybe consider 12 ton jack stands because the height of the transmission + the Harbor Freight hydraulic platform-style transmission jack was enough that it was an absolute PITA getting the transmission out from under the car and back in. The top edge of the bellhousing wants to contact the subframe and oil pan and if you're doing this on the floor forget about trying to lift this transmission off the ground and onto a transmission jack from under the car. Also do not try to use a scissor jack transmission lift. You have to rotate the damn thing in-place on the transmission jack which is hard enough with an adjustable platform and a transmission cradle that will mostly keep the transmission from rolling off the jack but on a scissor lift with a tiny non-adjustable platform? Forget it. Use penetrating oil on the driveshaft bolts. I highly recommend getting a thin 6 point combination (box end + open end) wrench for both the rear driveshaft and front driveshaft and a wrench extension. These bolts are on tight with very little space to work with and those two things together made a massive difference. Even a high torque impact wrench is just the wrong tool for the job here and didn't do what I needed it to do. If your starter bolts aren't seized in place for whatever reason you can in fact snake in a 3/8 inch ratchet + 6 point standard chrome socket up in there and "just" remove the bolts for the starter. Or at least I could. It is entirely by feel, you can barely fit it in, you can barely turn the stupid ratchet, but it is possible. Pull the front pipe/downpipe before you attempt to remove the transmission. In theory you don't have to, in practice just do it.  When pulling the transmission on the way out you don't have to undo all the bolts holding the rear driveshaft to the chassis like the center support bearing and the rear tunnel reinforcement bar but putting the transmission back in I highly recommend doing this because it will let you raise the transmission without constantly dealing with the driveshaft interfering in one way or another. I undid the bottom of the engine mount but I honestly don't know that it helped anything. If you do this make sure you put a towel on the back of the valve cover to keep the engine from smashing all the pipes on the firewall. Once the transmission has been pulled back far enough to clear the dowels you need to twist it in place clockwise if you're sitting behind the transmission. This will rotate the starter down towards the ground. The starter bump seems like it might clear if you twist the transmission the other way but it definitely won't. I have scraped the shit out of my transmission tunnel trying so learn from my mistake. You will need a center punch and an appropriate size drill bit and screw to pull the rear main seal. Then use vice grips and preferably a slide hammer attachment for those vice grips to yank the seal out. Do not let the drill or screw contact any part of the crank and clean the engine carefully after removing the seal to avoid getting metal fragments into the engine. I used a Slide Hammer and Bearing Puller Set, 5 Piece from Harbor Freight to pull the old pilot bearing. The "wet paper towel" trick sucked and just got dirty clutch water everywhere. Buy the tool or borrow it from a friend and save yourself the pain. It comes right out. Mine was very worn compared to the new one and it was starting to show cracks. Soak it in engine oil for a day in case yours has lost all of the oil to the plastic bag it comes in. You may be tempted to get the Nismo aftermarket pilot bearing but local mechanics have told me that they fail prematurely and if they do fail they do far more damage than a failed OEM pilot bushing. I mentioned this before but the Super Coppermix Twin clutch friction disks are in fact directional. The subtle coning of the fingers in both cases should be facing towards the center of the hub. So the coning on the rearmost disk closest to the pressure plate should go towards the engine, and the one closest to the flywheel should be flipped the other way. Otherwise when you torque down the pressure plate it will be warped and if you attempt to drive it like this it will make a very nasty grinding noise. Also, there is in fact an orientation to the washers for the pressure plate if you don't want to damage the anodizing. Rounded side of the washer faces the pressure plate. The flat side faces the bolt head. Pulling the transmission from the transfer case you need to be extremely careful with the shift cover plate. This part is discontinued. Try your best to avoid damaging the mating surfaces or breaking the pry points. I used a dead blow rubber hammer after removing the bolts to smack it sideways to slide it off the RTV the previous mechanic applied. I recommend using gasket dressing on the OEM paper gasket to try and keep the ATF from leaking out of that surface which seems to be a perpetual problem. Undoing the shifter rod end is an absolute PITA. Get a set of roll pin punches. Those are mandatory for this. Also I strongly, strongly recommend getting a palm nailer that will fit your roll pin punch. Also, put a clean (emphasis on clean) towel wrapped around the back end of the roll pin to keep it from shooting into the transfer case so you can spend a good hour or two with a magnet on a stick getting it out. Do not damage the shifter rod end either because those are discontinued as well. Do not use aftermarket flywheel bolts. Or if you do, make sure they are exactly the same dimensions as OEM before you go to install them. I have seen people mention that they got the wrong bolts and it meant having to do the job again. High torque impact wrench makes removal easy. I used some combination of a pry bar and flathead screwdriver to keep the flywheel from turning but consider just buying a proper flywheel lock instead. Just buy the OS Giken clutch alignment tool from RHDJapan. I hated the plastic alignment tool and you will never be confident this thing will work as intended. Don't forget to install the Nismo provided clutch fork boot. Otherwise it will make unearthly noises when you press the clutch pedal as it says on the little installation sheet in Japanese. Also, on both initial disassembly and assembly you must follow torque sequence for the pressure plate bolts. For some reason the Nismo directions tell you to put in the smaller 3 bolts last. I would not do this. Fully insert and thread those bolts to the end first, then tighten the other larger pressure plate bolts according to torque sequence. Then at the end you can also torque these 3 smaller bolts. Doing it the other way can cause these bolts to bind and the whole thing won't fit as it should. Hope this helps someone out there.
    • Every one has seemed to of have missed . . . . . . . The Mazda Cosmo . . . . . . what a MACHINE ! !
×
×
  • Create New...