Jump to content
SAU Community

Recommended Posts

Hey Guys,

well I put it off for as long as possible, but I just can't justify hanging onto her.


Selling a very clean, neat and close to stock standard genuine 1997 series 3 BCNR33 GT-R. With all the bits and pieces that make the series 3 that little bit nicer, like the red trim on the interior and the xenon headlights (which on this car are not cloudy and yellow like many others) In excellent condition, there are minimal non factory parts on the car. Do Luck floor brace, carbon fibre blade on the rear wing, carbon fibre look dash pieces, Blitz Dash Cluster showing 85344kms - real kms unknown but judge the cars condition, it's very tidy! HKS catback exhaust and a boost guage. I *think* that's about it. The engine is stock and has recently had a FULL service, including timing belt, water pump, tensioner etc. Also all new fluids throughout, new spark plugs etc - car has done no driving since all of that was carried out. This is no maintenance moneypit waiting to happen as all the big bucks have just been spent. Brand new tyres on the factory wheels.

Price includes RWC and 12 months registration

Inspections are welcome, happy to take the vehicle to a nearby workshop for a mechanical inspection as well. For serious buyers, I will arrange an unregistered vehicle permit for a test drive. Is fitted with an alarm/immobiliser and remote central locking also.

$20000 ono.

Contact through here or via email to [email protected] or phone at 03 90080031

post-58515-0-62618000-1380602222_thumb.jpg

post-58515-0-93333300-1380602229_thumb.jpg

post-58515-0-03384300-1380602239_thumb.jpg

post-58515-0-74341700-1380602245_thumb.jpg

post-58515-0-65199100-1380602252_thumb.jpg

post-58515-0-36983100-1380602258_thumb.jpg

post-58515-0-01107600-1380602265_thumb.jpg

post-58515-0-45419500-1380602273_thumb.jpg

post-58515-0-99688500-1380602281_thumb.jpg

post-58515-0-01554900-1380602289_thumb.jpg

post-58515-0-21193100-1380602296_thumb.jpg

post-58515-0-06719200-1380602305_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/432624-fs-mlb-1997-bcnr33-gt-r-in-white/
Share on other sites

I know for sure that I'd be struggling to find one in Japan in this shape and bring it in for these sorts of $$ nowadays, as the really clean GT-Rs are appreciating in value year on year over there

But I did price it tight in hopes of moving it on quicker, rather than putting a higher price tag on it and sitting on it for a few months waiting for the right person to come along.

hmmmm tempting, dunno if I can handle the power :)

Pfft softcock :P

GLWS regardless! Wish I could snap it up though, kinda the only car that'd get me back into Skylines.

Pfft softcock :P

GLWS regardless! Wish I could snap it up though, kinda the only car that'd get me back into Skylines.

haha, well maybe you should send me some info on this Caddy - probably an easier sell than a Skyline so it could work out ;0)

  • 7 months later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cleaner signal so timing is more accurate at all rpm also found it to start more on first rotation but could also be I've nailed prime and crank fuel. For under $400 and 30mins of your time, its a good solution especially once the optical sensor does start to play up you won't notice it until in higher rpm and it heat soaks.
    • On a 400hp RB, what benefits other than "it's not 30+ years old" are you seeing from the NZ Wiring Kit trigger setup? If it were me going to change triggering, my belief would be to go for a crank trigger to remove the issues caused by what people claim is belt stretch etc, but that's from my understanding a much larger issue for super high power, rather than those in the 400hp and below club.
    • The NZ wiring kit is a 1/3 the price and will be perfectly fine for your application, I've ran one for 6+ years and many others have. Comes as a full plug into factory connector and the settings for a Link. https://www.nzwiring.com/index.php/product/trigger-kit/ Always comes back to the tuners knowledge and experience with a tuning platform. It takes years to become proficient and learning all aspects and capabilities. I've been using Links for 16 years now (rb and sr paltforms) and always learning something new with adding tables, diagnostics and data logging. Stay 98 for the usability and keep it simple so you can enjoy the car more. With experience I'll give you a current example of the industry I am in. They use Motec m190 and only use VE tuning when they have a torque mapping available and would solve the "PARITY" issues that plagues the category all because the muppet doing the tuning doesn't understand the platform or want to learn it and the product seller have no idea on its full capabilities ( I had a good laugh as when firing up an older car that just got completed and they didn't understand the injector scaling or how to change it for different fuel being used)  
    • I'm sure there are specific hygrometers for it. But if you can just throw a high enough ranged temp sensor (theromcouple that came with your DMM, for example) into a pot of it on the BBQ, you can see when it boils.
    • I have multiple bottles in a shed that gets hot, and I'm in SEQ, so it's humid. Maybe we test their theory... Anyone have a system to accurately measure moisture content in oil?
×
×
  • Create New...