Jump to content
SAU Community

Recommended Posts

/Sold parts to 23 people.
Have 3 feedback thingo's.

/Awesome. :-|


Anyway.
Got more stuff.

1383412_645091675535877_1492568459_n.jpg
1376611_645091735535871_1199280826_n.jpg
Not in pic carpet/sumitomo calipers (obviously.)



I am open to offers, but parts are already reasonably priced.

If you turn up looking to buy $350 worth of parts and say you have $200 - you will be turned away. If you turn up with $300 - you have a deal.

Prices + Parts:

Wing Mirrors - $30 each. (One has mirror separation, the other has fade, both work fine.
149xxx odo, excellent cond. - $120
Drivers and passengers kick panels - $30 each.
Immac. Rear view mirror - $30
Fuse box cover, mint (Jap) - $10
Inner mirror covers (doors) - $10 each.
C.A.S Alloy bracket - $50
Coil packs on rails - $100
Drivers side lower vent, perfect nic - $15
Lower dash panel (covers fuse box, etc), immac. - $30
Door kick panels, good nic - $10 each.
Rear lower passenger trims - $40 each (One is missing the foam fabric insert, I do have it, it is also in good nic, just came off.)
Passenger A-Pillar trim, immac. - $20
Front lower guard "pods" - $25 each
Stock AFMS (working) - $40 each.
Dash temp/light sensor - $10
Rear eye-level brake light - $25
Indicator stalk and mechanism - $40
Sumitomo front 4 pot calipers - $180.
Carpet, mint - $200.


CAN POST SMALL ITEMS.
I would PREFER you pick up though.

Feel free to lowball me - you will be ignored. :yes:

Located in Hornsby.


PM ME OR TEXT ME.
Please do not post here, I wont be checking back here other than to post what is sold.

Ok guys.
It's all getting thrown out if it doesn't sell by the end of this coming week.
Perfectly good coil packs, wing mirrors, lower rear passenger trims, center console "triangle" trim piece.
Kick panels, and door scuff plates.
And what is still on that list ^^^^^^^^^^

  • 2 months later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
    • Kinda something I have been thinking about.  To be honest, we bought it already driving like that.  So there's no telling how long it actually has been driving like this.  Hopefully damage is too bad when we drop the pan.   I am having a hard time finding a site that sells the solenoid for the 5 speed auto, do you have any suggestions?
    • That'll be most likely down the road...  LOL  
    • a stock / option or aftermarket?
×
×
  • Create New...