Jump to content
SAU Community

Recommended Posts

my Nur had Nismo injectors before i changed, they were fine for 350'ish rwkw, running 2530's.

Proven, solid injector. I'm in Melb as well. I'm sure i can help you out with a good price just to get you passed these injector issues :)

I tryed to pm you but it won't work just keeps giving me an error message. Don't know what's up. Are the nismo injectors going to fit in my 32. And are they the same cc because I can't tune yet haven't got power fc.

  • 2 weeks later...

Hey guys I purchased a power fc and controller and second hand denso 550cc injectors

I was just wondering if I can put the injectors in now without the power fc because all the workshops are closing up for chrissy. Will it still run ok or should I wait till power fc gets installed and tuned? Thanks guys

Hey guys I purchased a power fc and controller and second hand denso 550cc injectors

I was just wondering if I can put the injectors in now without the power fc because all the workshops are closing up for chrissy. Will it still run ok or should I wait till power fc gets installed and tuned? Thanks guys

You can setup the injectors in the PowerFC, but you'll need to know the latency of the denso 550s or the idle & low throttle fuelling will be off. Also, you'd be taking a bit of a gamble on the motor if you drive it hard before getting the tune checked after the injector swap.

I would be getting any S/H injectors flow tested before fitting them, injectors sometimes don't like being removed from a fuel system and left on a shelf for a few months. Were they stored in a sealed bag or similar at least?

One slightly blocked injector can really ruin your day... I hope you got them cheap as new injector prices are dropping fast.

Yer the guy took em out of his car cloth baged em bubble warped and boxed and express posted them hense why I was thinking of putting them in the car straight away. I can't get the car booked in till the 6th of jan so I wasn't sure if the injectors will be ok sitting till then or is there a good way to store them ?

Not really, just keep them in a sealed sandwich bag or similar. I would replace the 'O'rings too if they have any sign of damage, and lube them up well before installing them, you don't want petrol leaking over a hot engine.

I use a little silicone spray to lube the Orings..

  • 4 weeks later...

ok so injectors in power fc in tuned and dyno'd came back with 245kw on 14psi

feels much nicer to drive has realy changed how the boost comes on its a bit more punchy,

im thinking i might need some more mods soon tho to gain a bit more power 300kw would be nice i think :)

ok so injectors in power fc in tuned and dyno'd came back with 245kw on 14psi

feels much nicer to drive has realy changed how the boost comes on its a bit more punchy,

im thinking i might need some more mods soon tho to gain a bit more power 300kw would be nice i think :)

All you need is 22psi crammed down it's throat, as long as the fuel system can keep up. Seems to be making good power for the low boost you are running atm.

Having some problems at the moment guys hoping some one can help, I was driving home this arvo and stopped got fuel, drove like 10ks car started spluttering losing power for a second then come good, keep driving same thing splutter a bit then come good. Then I'm doing 80 up hill and it just keeps dropping power and I pull over off the road and it just stalls started up again stall, start up again keep driving not too bud a couple of little splutters then get to the end of the street turn the corner and stall in the middle of the road got it home but worried what it may be dirty fuel pick up from when I fueled up, coils, afm

Any help would be muchos appreciated

Well lets go through process of elimination.

Car drives good -> Stop -> Fill up -> drive off -> car is shit

In conclusion, all evidence points to the variable that you exposed yourself to, the fuel. Therefor empty tank with syphon, go to good petrol station, put in fuel and see if that was the problem.

Well I filled with bp ultimate as I usually do, the fuel light wasn't on its not like the tank was bone dry picking up all the shit at the bottom. And I'd have thought it would caugh and fart within a few minuets of driving if it was bad fuel or shit from bottom of the tank. It used to have a little bit of a loss of power moment before I got the injectors and the ecu done but my mechanic said that looked to be a faulty relay for the fuel pump and they replaced it.

if your car was driving 100% before you filled up.

I dont see how something coincidentally broke at that exact moment unless you mistook your engine bay as the fuel tank.

Also, when you fill up, it sloshes around and mixes together. Its not a layering system

running a tank dead dry will not allow the pump to pick up dirt lol where do you think the sock sits that picks up the fuel? I can tell you now it aint at the top of the tank or you would never drive long enough to see the gauge drop

Take the car back to the dyno if it can be driven and get it on there to see what its doing. Sitting behind the laptop is not going to sort it out any time soon. You have said ages ago that the car used to splutter and stall and clearly the mods now done to the car have not changed anything so there is something else that needs attention

Who tuned it?

With regard to turbo upgrades, take a look into the new Precision Turbo GTR replacements. From what i have seen they should be good for some pretty decent power. Just run them at low boost ;)

Edited by ido09s

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Can perhaps see how the R33 appreciators would think so.  
    • Thanks, I removed the fuse and the relay from the car and made my own circuit with them to test them with a test bulb.  I will look for the wiring diagram and go from there.
    • Jdm DC2R is also nice for a FF car compared to the regular hatches of the time.
    • Now that the break-in period for both clutch and transmission is nearly over I'd like to give some tips before I forget about everything that happened, also for anyone searching up how to do this job in the future: You will need at least 6 ton jack stands at full extension. I would go as far as to say maybe consider 12 ton jack stands because the height of the transmission + the Harbor Freight hydraulic platform-style transmission jack was enough that it was an absolute PITA getting the transmission out from under the car and back in. The top edge of the bellhousing wants to contact the subframe and oil pan and if you're doing this on the floor forget about trying to lift this transmission off the ground and onto a transmission jack from under the car. Also do not try to use a scissor jack transmission lift. You have to rotate the damn thing in-place on the transmission jack which is hard enough with an adjustable platform and a transmission cradle that will mostly keep the transmission from rolling off the jack but on a scissor lift with a tiny non-adjustable platform? Forget it. Use penetrating oil on the driveshaft bolts. I highly recommend getting a thin 6 point combination (box end + open end) wrench for both the rear driveshaft and front driveshaft and a wrench extension. These bolts are on tight with very little space to work with and those two things together made a massive difference. Even a high torque impact wrench is just the wrong tool for the job here and didn't do what I needed it to do. If your starter bolts aren't seized in place for whatever reason you can in fact snake in a 3/8 inch ratchet + 6 point standard chrome socket up in there and "just" remove the bolts for the starter. Or at least I could. It is entirely by feel, you can barely fit it in, you can barely turn the stupid ratchet, but it is possible. Pull the front pipe/downpipe before you attempt to remove the transmission. In theory you don't have to, in practice just do it.  When pulling the transmission on the way out you don't have to undo all the bolts holding the rear driveshaft to the chassis like the center support bearing and the rear tunnel reinforcement bar but putting the transmission back in I highly recommend doing this because it will let you raise the transmission without constantly dealing with the driveshaft interfering in one way or another. I undid the bottom of the engine mount but I honestly don't know that it helped anything. If you do this make sure you put a towel on the back of the valve cover to keep the engine from smashing all the pipes on the firewall. Once the transmission has been pulled back far enough to clear the dowels you need to twist it in place clockwise if you're sitting behind the transmission. This will rotate the starter down towards the ground. The starter bump seems like it might clear if you twist the transmission the other way but it definitely won't. I have scraped the shit out of my transmission tunnel trying so learn from my mistake. You will need a center punch and an appropriate size drill bit and screw to pull the rear main seal. Then use vice grips and preferably a slide hammer attachment for those vice grips to yank the seal out. Do not let the drill or screw contact any part of the crank and clean the engine carefully after removing the seal to avoid getting metal fragments into the engine. I used a Slide Hammer and Bearing Puller Set, 5 Piece from Harbor Freight to pull the old pilot bearing. The "wet paper towel" trick sucked and just got dirty clutch water everywhere. Buy the tool or borrow it from a friend and save yourself the pain. It comes right out. Mine was very worn compared to the new one and it was starting to show cracks. Soak it in engine oil for a day in case yours has lost all of the oil to the plastic bag it comes in. You may be tempted to get the Nismo aftermarket pilot bearing but local mechanics have told me that they fail prematurely and if they do fail they do far more damage than a failed OEM pilot bushing. I mentioned this before but the Super Coppermix Twin clutch friction disks are in fact directional. The subtle coning of the fingers in both cases should be facing towards the center of the hub. So the coning on the rearmost disk closest to the pressure plate should go towards the engine, and the one closest to the flywheel should be flipped the other way. Otherwise when you torque down the pressure plate it will be warped and if you attempt to drive it like this it will make a very nasty grinding noise. Also, there is in fact an orientation to the washers for the pressure plate if you don't want to damage the anodizing. Rounded side of the washer faces the pressure plate. The flat side faces the bolt head. Pulling the transmission from the transfer case you need to be extremely careful with the shift cover plate. This part is discontinued. Try your best to avoid damaging the mating surfaces or breaking the pry points. I used a dead blow rubber hammer after removing the bolts to smack it sideways to slide it off the RTV the previous mechanic applied. I recommend using gasket dressing on the OEM paper gasket to try and keep the ATF from leaking out of that surface which seems to be a perpetual problem. Undoing the shifter rod end is an absolute PITA. Get a set of roll pin punches. Those are mandatory for this. Also I strongly, strongly recommend getting a palm nailer that will fit your roll pin punch. Also, put a clean (emphasis on clean) towel wrapped around the back end of the roll pin to keep it from shooting into the transfer case so you can spend a good hour or two with a magnet on a stick getting it out. Do not damage the shifter rod end either because those are discontinued as well. Do not use aftermarket flywheel bolts. Or if you do, make sure they are exactly the same dimensions as OEM before you go to install them. I have seen people mention that they got the wrong bolts and it meant having to do the job again. High torque impact wrench makes removal easy. I used some combination of a pry bar and flathead screwdriver to keep the flywheel from turning but consider just buying a proper flywheel lock instead. Just buy the OS Giken clutch alignment tool from RHDJapan. I hated the plastic alignment tool and you will never be confident this thing will work as intended. Don't forget to install the Nismo provided clutch fork boot. Otherwise it will make unearthly noises when you press the clutch pedal as it says on the little installation sheet in Japanese. Also, on both initial disassembly and assembly you must follow torque sequence for the pressure plate bolts. For some reason the Nismo directions tell you to put in the smaller 3 bolts last. I would not do this. Fully insert and thread those bolts to the end first, then tighten the other larger pressure plate bolts according to torque sequence. Then at the end you can also torque these 3 smaller bolts. Doing it the other way can cause these bolts to bind and the whole thing won't fit as it should. Hope this helps someone out there.
×
×
  • Create New...