Jump to content
SAU Community

Buddy Club P1S

slidnreds13
 Share

Recommended Posts

slidnreds13 Rising Star

slidnreds13

Posted
Posted

Hey guys, up for sale are my 17" Bronze buddy club p1s
They are 17x9 +20 all round and you dont often see them in these sizes.
They all have Federal 595s that are around 2000kms old and im running basically 0 camber so theres no uneven wear!
All are in good condition, no buckles but just a little rash on one.

Im asking $1500 as im in no rush to get rid of them but it would be nice to have some extra money for when i go overseas in 2 months so if you have money then feel free to come have a suss of them and make an offer,
My number is 0427979096 and im located way down south in port elliot but am always up in adelaide so i can deliver them, also postage is fine but at your cost obviously.

http://classifieds.nissansilvia.com/index.php?t=2315815&view=advert

Link to comment
https://www.sau.com.au/forums/topic/433880-buddy-club-p1s/
Share on other sites
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Watermouse
      Hypergear Turbochargers and High flow Services Development thread

      By Watermouse · Posted

      That’s a beautiful setup Tao, Have u done any development with the new Turbosmart 40mm electronic straight gate, especially in this G30 configuration?
    • Dose Pipe Sutututu
      Neil's R33 Gts-t Build

      By Dose Pipe Sutututu · Posted

      Let's hope that's not a copy pump either. There were so many copies of them back in the day.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Damn it, I was at work last night, and stayed in a room there during the storm with the car outside, but undercover, I just went downstairs and well....there was a large steel locker that has come from some place last night, it wasn't anywhere I could see yesterday, and yeap, it landed on the fraking car....of course it did..... LOL So, I'll need to take it back for paint and panel, luckily it was only the boot that took the hit, so it could have been worse Serves me right for staying at work and getting on the cans with some of the boys
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, really happy with how it all turned out As for aftermarket lip, nah, I'm not really a fan for practically reasons on a street car that gets driven everywhere  I did have the full lower kit on my 2015 STI, but found the front lip scrapped alot, even at stock 4x4ish ride height As the NC sits now, with the lowest point of the car at 110mm, so just legal, some steep driveways and steep speed humps will still "just" scrap those little plastic OEM air dam thingies on the undertray just before the front wheels
    • Dose Pipe Sutututu
      Hypergear Turbochargers and High flow Services Development thread

      By Dose Pipe Sutututu · Posted

      Here's one I help build and tuned a decade ago, Garrett  GTX3071R Gen 1, T3 twin scroll 0.83 rear housing. Went from larger 272 cams down to smaller Tomei Poncams to help with the low end. S13 non VCT motor. Car was purpose built for the track, hence low down was the focus. Note the actual dyno chart shows lower boost, however the EBC and boost gauge showed 1.9Bar (Ignore the torque, I was young and didn't know how to set derived torque)  
×
×
  • Create New...