Jump to content
SAU Community

Recommended Posts

All to suit R32 GT-R, all BRAND NEW IN BOX:

1. D1 spec carbon look bonnet latches - $50 (will suit any car)

2. Nismo braided clutch line - $85

USED PARTS:

1. Nismo lightweight flywheel - $250 (http://www.nismo.co.jp/en/products/competition/clutch/pdf/clutch07.pdf)

All BRAND NEW to suit R32 GTR, NISSAN PARTS:

1. BM57 brake master cylinder (ABS type) - $375

2. Clutch MC booster - $200

3. Clutch master cylinder - $150 ($330 package price with booster)

4. Have other items inc ball joints, steering rack boots, thermostat + housing, etc

All prices are + postage

Txt/call me on 0407 175 417 and I will send you through photos asap

Cheers

  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...

Pm me pic of the mines pipes and the do-luck hardline

Thanks

Nic

Hi Nic

Unfortunately those items sold long ago. See below for what is still available

Cheers

BRAND NEW IN BOX:

1. D1 spec carbon look bonnet latches - $50 (will suit any car)

2. Nismo braided clutch line (R32 GTR only) - $85

USED PARTS:

1. Nismo lightweight flywheel - $250 (http://www.nismo.co....f/clutch07.pdf)

All BRAND NEW to suit R32 GTR, NISSAN PARTS:

1. BM57 brake master cylinder (ABS type) - $375

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I chose a bad time to buy, at the time there was no gtst's for sale in NSW and my options were qld, vic, or sa and not the greatest examples or too far out of my budget. Ended up picking this one from adelaide sight unseen and got a bit stitched up as you could expect but i dont fully regret it, its just a shame people cant be more transparent in this day and age.
    • IMO just buy a whole R33 transmission and swap the whole thing. Use a palm nailer/air hammer with a roll pin punch to drive the shifter rod end roll pins out. The rod end is discontinued so don't break it. Use gasket dressing on the OEM paper gasket instead of RTV. I personally would not pry on the shifter cover tabs, I broke one trying that instead of just smacking the side with a dead blow rubber mallet to shock it loose from the RTV the last mechanic applied. If you can't get the flanges totally clean and free of any residual RTV and/or you might have a gap that is bigger than it should due to flange damage use RTV on that surface instead of the OEM specced anaerobic sealer. Anaerobic sealer is most likely the right sealant for the job, it's just too easy to mess it up with too large a gap or bad surface prep/roughness seemingly. If you do rebuild what you have it's for a whole gearset that can take high torque. Don't bother with OEM at that point.
    • Little hose. Big hose. They're all waiting to kill the engine.
    • Nice ride, hard to find these days!
    • Full e85 barrell stuff real world for reference if it helps as Ive pushed 2 x sets injectors to limit Above mentioned Bosch 1480cc run on 4 bar base to the apparent 1650cc on rb2.7 yielded 912hp / 684  kw  at 92% duty on hub dyno ID1700's - RB 2.8 ...1015hp / 760 kw at 87% duty - hubber dyno + shown off data on track my opinion IF you change injectors just go bigger than you think you need the modern/ good larger ones run just fine if tuned properly even if way bigger than required even on streeters  
×
×
  • Create New...