Jump to content
SAU Community

Recommended Posts

Event:
Happy Laps - Lakeside Park

Description:
A chance to get out on track for a fun cruise and have some om nom noms! Bit of spirited driving is allowed but it is still an event on a race track so a few rules need to be followed (see below). Breakfast will be served with bacon, eggs, beans and toast.

Location:
Lakeside Park
Link To Map.

Date:
Sunday 12 January 2014

Time:
7:00 AM Arrival
7:30 AM Breakfast
8:00 AM On Track

Cost:
$35 for members and guests of members riding/driving the members car.

$50 for non members.
Please note that this is a per person cost, any passengers are required to pay as well.
If you wish to come along to watch and not have breakfast it is free.

Requirements:
1. Participants must meet minimum age requirements for being on track. Minimum age: 12yrs old.
2. No overtaking in the first 2 laps.
3. The overtaking car is responsible for completing the overtaking move safely.
4. Overtaking is only permitted on straights, unless clearly waved passed by the car in front.
5. Overtaking move must be completed well before the end of the straight, and the car being overtaken must be given plenty of room.
6. Cars should not be more than 2 abreast at any point on the track.
7. Be aware of cars around you, in front and behind (and beside when being overtaken).
8. Do not assume that the car in front of you knows you are there.
9. Please pay cash on the day, no EFTPOS is available.
Lakeside Specific Rules:
10. Members must have completed at least ONE QR Happy Laps before participating in a Lakeside session. (If you have done other Lakeside events before you may be eligible. PM me to clarify)
11. No overtaking or cars side by side on the kink.

Payment Details:

Name: Skylines Australia Queensland Club

Bank: Westpac

BSB: 034 063

ACC: 354012

PAYMENT REFERENCE: Username&HappyLaps

Attendees:

1. Cadmoon

2. t5iv

3. HiveFleetAbyss

4. cowdy

5. Cyifly

6. AndrewK34 +1

7. Bodo

8. Shi Pi

9. gts032

10. Kiwi_Phil

11. Kiwi_Phil's +1

12. ARE31 +1

13. B-Boi34 +1

14. Bubbles

15. Bubbles' +1

16. Bubbles' +2

17. Tohmez

18. Smity42 +1

19. Wolfman101

20. Ralph

21. courtoR33 +1

Link to comment
https://www.sau.com.au/forums/topic/434078-lakeside-happy-laps-120114/
Share on other sites

Since QR now require a minimum of 30 people (drivers and passengers) per session we will see how this LP session goes, if we get enough people we will be able to keep the price at $35 but if we cant get numbers we will have to bump the prices to cover the numbers.

if everyone that says they will turn up,actually turned up there would be no problems,if you cant go just say so,makes it hard enough for the club to organise these events as it is,let alone being shagged around,this is for you people!!!!

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There are a few different ways of doing it. I'm currently running two 1000cc pre-TB nozzles and PWM the pump for control. I'll be moving over to a constant pressure system and direct port. I'll run the pump off a regular relay, have it cycle on roughly 5psi before I start injecting to build pressure and then PWM a WMI solenoid (It's basically an injector that can take a lot of pressure and not corrode with water and meth.) The solenoid feeds the 6 direct port ~200cc nozzles. I'll also keep one ~250cc pre-TB nozzle to help keep IAT's in check.  Safety will be a little different as well. I used to use a pressure switch but will be moving over to a pressure sensor between my solenoid and nozzles. I'll trigger my solenoid and if I don't see specific pressure within a specific timeframe (e.g 100psi within a second, 175psi within 2 seconds), I kill it and revert back to non WMI maps the same way I did it before with 4D in Haltech. I was just figuring out the timers in my ecu last night. They made that a little more complicated than I would have liked... I wish Haltech offered a larger set of logic/math functions like other ecu's do. I can't do very much with just AND's and OR's.  I've been asked to do fuel/ignition mapping on a medium bore engine at work in May (192L V16). Being the only programmer in my region and having went and opened my mouth about knowing the ins and outs of fuel/ignition mapping, I have now been deemed an expert. Fun fun. The entirety of the logic and algorithms are programmed in C on a PLC. As I spend more time figuring it all out, I like what I see and eventually I may consider doing the same as a pet project to replace my ecu.   
    • This would be interesting, would you feed it via a 2nd row of injectors? Or just usual WMI nozzles?
    • Cut sump up and extend. Win win 😂 
    • All, What's the recommended torque for the 1/2 head studs for RB30 twin cam conversion with RB26 head?  
    • also, we need to know which solution worked....
×
×
  • Create New...