Jump to content
SAU Community

Wrecking R32 Gtr! Mint Complied Shell And Heaps Of Parts!

Deano_Drifter
 Share

Recommended Posts

Deano_Drifter Community Regular

Deano_Drifter

Posted
Posted

ok guys and girls parting out r32 GTR.

everything located gold coast.

list of parts:

*complied shell bare with: doors, mirrors, front crossmember, front suspension (byo wheels and it will be rolling), body loom, all glass, steering rack. registerable $1300ono

*aftermarket front dump twin 2.5" to single 3 or 3" to cat $250

*RB26 long motor with no intake or turbo side and gearbox with exedy cushion button clutch $2500

*boot $150

*rear pods $150

*mint dash with all vents $300

*mint carpet $150

*tail lights $100

*complete centre console with stereo surround, ash tray and nice black leather/red stiching $250

*both door trims with custom splits/tweeters $200

*rear bar with reo $150

*heater boxes n shit $100

*centre gauges $150

*brake master and booster $150

*clutch master and booster $150

*brake pedal $75

*clutch pedal $75

*twin bov setup with all the piping to suit (plumb back) $150

*fuel rail and injectors $200

*wheel arch trims $50

*brand new bonnet hasn't even seen paint $500

pm or call for more info 0403423121

cheers.

Link to comment
Share on other sites
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Lithium
      Boost level and torque curve

      By Lithium · Posted

      There is a LOT of stuff that can be done, it all depends on how much time and money you want to spend on doing in.  Not all ECUs will be able to do it, and the more control you need the more time and knowledge needs to be put into making it work.  If you're willing to spend the time and money and have the right hardware and skills involved there's a lot that can be done. 
    • thx78
      Boost level and torque curve

      By thx78 · Posted

      I am impressed with all this level of adjustment. I didn't expect all this possibility
    • Lithium
      Boost level and torque curve

      By Lithium · Posted

      Correct.  In the case of the 500kw dyno plot I showed you the car actually runs two boost control solenoids for boost control and a 5psi wastegate spring.  It allows me to control how much boost pressure is applied to both sides of the wastegate valve at any point and fairly accurately control boost target as a result. I've tuned it so that it's able to target anywhere from 5psi to 25psi depending on what's needed.  The target tables I've set up in that car are Gear vs RPM, so every gear has potential for a different boost (and torque) curve.   First and second gear have quite low boost targets, third gear actually has different target boost all the way through the rpm range as it's a stock RB25 gearbox - the boost targets have been chosen to maintain a peak of 600nm (what the owner has set as the maximum torque he's happy with putting through the stock 3rd gear) but it carries that to the rev limiter.   The boost curve to achieve that is something of a ramp up, then hold, then ramp up again and the power curve looks more like a flat line haha.  
    • thx78
      Boost level and torque curve

      By thx78 · Posted

      so you can decrease or increase the boost depending on the diet as you wish?     by acting on the wastegate?
    • Lithium
      Boost level and torque curve

      By Lithium · Posted

      That's torque and power, it's all from a single run.  The boost curve is "held back" from it's peak target in the 3500rpm to 5000rpm range from memory, so it ramps hard to something like 18psi then climbs more progressively to 23psi nearer 5000rpm.   It makes the torque (and power) ramp more "natural" and less hard on parts and traction, it doesn't feel artificially held back.   
×
×
  • Create New...