Jump to content
SAU Community

Recommended Posts

Harro,

I have a split dump dump from 999 Automotive I want to sell, reason being it's about 1cm shorter than the stock one which causes my down pipe to touch the underside of my car. Having OCD, I don't like that so I've installed the stock one back again.

Same one as this, purchased from the same store. I have receipt which is included in the sale.

http://www.ebay.com.au/itm/KLS-EXHAUST-TURBO-twin-entry-DUMP-PIPE-NISSAN-SKYLINE-RB20-RB25-R32-R33-R34-/330890072292?pt=AU_Car_Parts_Accessories&hash=item4d0a95d0e4&_uhb=1

However, I've enlarged the holes to fit, removed the stupid divider (was hitting my wastegate flap).

So what you get is something that will fit straight up with out any mods, includes:

* Dump

* A bunch of bolts and washers

* No gaskets

* No divider piece (I chucked it out, on testing with an air compresser it hits that thing)

Save yourself some coin.

$50

Pickup from Canley Vale, NSW, 2166

Reply here or PM

Here are some photos...

I had to work this ling long piece of shit product to fit.

  • Hole have been enlarged
  • Casting marks smooth out with a flap disc
  • Divider removed
  • Proper fitting bolts purchased (nuts/studs provide did not fit)

Oh yeah, free working factory O2 sensor!

$T2eC16hHJIcFHOBy7VepBSeNsI5sBw~~60_58.J

$(KGrHqVHJBMFJipNVsodBSeNupU3bw~~60_58.J

$T2eC16ZHJH8FHQqI,,h,BSeNwdl1Hg~~60_58.J

I had the same thing, my down pipe from them was about 2 to 3 inches short, I had to cut in and weld in a section to lengthen it, had no choice. Good luck with the sale mate

or use a spacer/flange to make it longer...

I'm going v band next so no need for this ling long bullshit lol

Free for me?

for a slab of blonde and I ain't fitting it... I don't want to snap dump bolts (always happens) lol

for a slab of blonde and I ain't fitting it... I don't want to snap dump bolts (always happens) lol

Just playin. Ain't no body got time for ling long shit!

hahahah that's right!

Unless you're not anal like me, I hate shit that doesn't fit.. gets on my nerves

  • Like 1
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Get a timing light on it and verify it's sparking reliably at a sane ignition timing. Use a COP extension lead to be 100% sure about timing instead of hoping that the timing loop on the back of the engine is accurate. Make sure it's actually injecting fuel. MAF is not used on the stock ECUs for initial cranking.
    • RE5R01A is the transmission. Didn't realize they had a 5 speed for the NA cars but for some reason the turbo engines stuck to 4 speeds. Looks like the solenoid block is still available from Nissan directly at a somewhat reasonable price: 31940-60X01 https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/skyline/er33/6568-rb25de/trans/317 I would move sooner on this than later. The moment the de minimis exception for Japan goes away expect to be paying 25% tariffs even for stuff like this.
    • Only RB26 are low from factory. And even then the ECU actually want high impedance, because it's essentially the same ECU as the RB20 anyway, and thus they have a f**king resistor pack!
    • Is this preventable by priming the system with external oil pressure? I've seen the speed academy folks hook up an external oil priming system to the oil pressure sensor port with an air compressor to check for oil leaks before putting an engine back in a car. Something like this: https://www.jegs.com/i/JEGS/555/23550/10002/-1?gPromoCode=SPRINGINTOSPEED_APR25_5Off&gQT=1
×
×
  • Create New...