Jump to content
SAU Community

Recommended Posts

I get on average 260Kms a tank with my GTT aswell. Engine wise it's completely stock. I've cleaned AFM changed the fuel filter, fuel filter was completely clogged I noticed a slight difference in fuel consumption, maybe I'll have to go for the O2 sensor and new plugs see if that helps as well

Also if someone has put a low temp thermostat in, or yours is stuck open, then that will also add to poor fuel efficiency. Cold crank enrichment tapers off at 70C so the quicker she gets up to temp the better.

This. I put a Nismo thermostat in my Riceline, water temp now sits at 60C unless I'm at a track day. I struggle to get 12L/100kms, when I first bought the car I easily got 9.5L/100kms on the highway

I do do alot of short trips, I'm running PFR8 plugs with a 0.9 gapp,

Short trips, incorrect heat range plugs - no wonder you have absolute crap economy.

Try running a 6 heat range for starters. And plan your trips better so the engine operates at the correct temperature for most of the time.

So OEM/stock thermostat is best for fuel economy? What about oil cooler with built-in thermostat?

Mines got a oil cooler with no thermostat, oil temp sits between 70-80 degrees. I run BCPR6ES plugs with the standard gap, which is 0.8mm from memory.

I've found V Power to give me greater mileage than BP Ultimate for some reason too

I ran those before the PFR8S and it was the same thing, well the owner in Japan did fit quite a few Nismo parts to the car, I'll check what thermostat is in there and give the AAC valve a clean aswell, is there a way I can get error codes through a power fc by any chance, thanks.

And whats the difference between the BCPR6ES and the BCPR6E? And could some refresh my mind the lower the number the higher the plug temp correct? thanks.

Edited by MrRx7s3

Yep lower number is hotter. Has anyone checked their timing? That would have an impact on economy. Also should be talking litres per 100 ks as too many variables with a 'tank' of fuel.

true but seriosuly when were talking a difference of 550km- 250km, i dont think brimmed vs filled is going to mean too much.

Its not the difference of how full, but how empty it is when you fill it. Accuracy of fuel gauge and how far you are willing to with the gauge below the E.

mine been tuned a while back after i re-did my fuel pump mod for battery voltage, crap economy, around 300km on full (72L tank IIRC), o2 sensors turned off, bcpr6es plugs, no leaky injectors, although i do short trips (10km) each way to work, low temp sender perhaps buggered?

mine been tuned a while back after i re-did my fuel pump mod for battery voltage, crap economy, around 300km on full (72L tank IIRC), o2 sensors turned off, bcpr6es plugs, no leaky injectors, although i do short trips (10km) each way to work, low temp sender perhaps buggered?

Install a wideband o2 and see what your car is doing. I've seen lazy tuners who don't even care too much about off boost injection maps and just rely purely on o2 closed loop to work out the mixtures.

I find mine is chewing up a fair bit of petrol as well. I've put some fuel injector cleaner in which should help, also going to replace the spark plugs and clean the AFM sensor to see if that makes a difference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The hot exhaust light will come on not from just the cat being blocked, but it's just a temp sensor, and it's designed to warn you to not do things like park in long grass.   If you've been pushing the motor a bit, it can cause the light to come on.   Second if the cat is rattling, I'd suspect it's not blocked, but instead falling apart inside.   The easiest "fix" until you can get a cat put back in, is to unbolt your one, bash the rest of the insides out, and then bolt it back in.   For a daily driver/street car, I am in agreeance of put a cat in the car. If it were race car I wouldn't care if it were removed.
    • No worries at all 🫡 I think the most satisfying things to make are the little bits that are just impossible to find or they're no longer manufactured. Generally I always try to replace parts with OEM wherever possible. This little project is also great because it'll never see the light of day, but strengthen these brackets so it's not just relying on the little standard screws in the headlight plastic. As soon as I saw the standard brackets and screws I thought, "well I'm not going to install with just the screws, the plastic tabs will just snap off". It's crazy how expensive everything has become yeah. But I suppose that's supply and demand; granted it's a lot easier to get brand new genuine parts these days which is fantastic 😊, I don't have to get totally reamed at the local Nissan dealer ha ha We sure are lucky we have all these manufacturers making parts these days, a few really great Australian companies too like Platinum Racing Products and Fit Mint Automotive, what a time to be alive ❤️ . I've got my eye on the RB26 head by PRP as mine has a very fine hairline crack, so that'll need to be addressed some time in the future. If you have any requests or odd things to make feel free to let me know and I can have a crack at making replacement parts ✌️
    • Thanks for sharing this, and BTW if your headlights are in good condition they are worth thousands....you might want to consider replacing them with brand new LED ones like this (https://www.nengun.com/78works/full-led-headlights-r32-skyline) and making enough profit to buy a house in Sydney
    • I'm not sure what sort of shops are nearby, but I'd expect any reasonable exhaust shop could put a cat in it that will not restrict the power that engine makes. Otherwise, if you want to remove it, short lengths that replace the cat are readily available online, search for "de-cat pipes" or "test pipes"  
    • Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
×
×
  • Create New...