Jump to content
SAU Community

Recommended Posts

I am told that everything to change the clutch has arrived, so all going well I will be able to get it booked in for the clutch swap next week.

In the meantime I have been working on the fuel system again. My powerhouse fuel hat melted another electrical bulkhead seal, so instead I've re-fitted it with an o-ring seal this time. WIth any luck this will solve the fuel smell in the car issue.

I've also decided to do away with the external surge tank, and spent the afternoon in the boot of the car trying to shoehorn a pair of 044's in there. After about 3 hours I finally got them in there and mounted. What a mission. I think that triple walbro's would have been a lot easier.

Here 's a few pics of the PHR fuel hat for those that haven't seen them.

post-26553-0-69542800-1435394167_thumb.jpg

post-26553-0-64439700-1435394191_thumb.jpg

The R35 brake setup that I've gone with isn't exactly a typical setup. It took a bit of work to get it in there but the results are very impressive.

The front rotors are 390mm Alcons with factory R35 callipers and endless calliper adapters. The pads are PMU carbon. The bite is good cold, but when hot they are mind bogglingly good. I have to do a 100-0 brake test at some stage.

Rear rotors are DBA 380mm T3. The factory handbrake is used.

No issues with the master cylinder size. From what Ive read on the UK forums, the R34's MC is bigger than the 32/33's and is considered acceptable to use with the R35 callipers.

post-26553-0-01356000-1435394798_thumb.jpg

Always good to read the updates, this is one of the most interesting projects on here.

A couple of these would have been easier to fit in-tank than the 044's

http://www.nzefi.com/product/walbro-465lph-in-tank-fuel-pump-supports-700hp/

Looking forward to the updates when the clutch is in

I actually tried a walbro 460 as a lift pump at one stage, and discovered they need to have the base of the pump wet in order to prime.

The mount for the fuel pump in the R34 is half way up the height of the tank, with a long pickup hose that goes down into the sump of the tank. I believe I needed around 500-550lt/hr at 75psi to meet my power goal.

There is two types of wire on the PHR fuel tank hat. Two small grade wires for connecting to the gauge sender circuit, and the other wires are much larger. Its milspec wiring with thin insulation and silver plated conductors. It will easily handle 20A.

  • Like 1
  • 1 month later...

Update time again.

Today was D day for testing of the engine. New clutch installed, 200lt of E85 at the ready no excuses.

After some minor issues were resolved, the 98 octane tune was completed yesterday. With 18lb we reached the knock limit at 384kw/514hp atw on the dyno dynamics AWD dyno.

Then this afternoon I drained the tank and filled with the first tank full of E85. Due to the remaining 98 in the lines and tank though the mix ended up being E60.

Trent went to work, and after resolving issues with a few intercooler hoses refusing to stay put, 457kw/612hp atw was reached. At this point the map sensor was maxed out (28lb).

Also it appeared the 1.0 housing on the 6466 had become a restriction, as power was dropping off in top end.

While I didnt reach my 500kw goal Im very happy with the result. It makes positive manifold pressure at 1800 RPM and full boost somewhere around 3200-3300, where it pulls like a mad man to redline.

I've got a fair bit of video to put together, so i'll do that in a day or so.

In the meantime, a few pictures.

post-26553-0-61032400-1438519199_thumb.jpg

post-26553-0-78535300-1438519224_thumb.jpg

post-26553-0-20946300-1438519238_thumb.jpg

post-26553-0-31968000-1438519267_thumb.jpg

  • Like 2

6466cea 1.0 hot side.

28lb (maxed 3 bar map sensor).

Unfortunatly the RPM signal was not hooked up during the tuning. The gear ratio torque calculation method was used on the last BP98 runs, and that made 712nm. No idea with E85, but safe to say its a lot more.

Mmm torque.

How far do you think you'll take this? 600 hp seems like a small number for that engine.

The map sensor is maxed out. It would need a 5 bar sensor to go any further. Running at 27-28 psi leaves little sensor head room to detect a over-boost condition, allowing over boost cut to protect the engine. It was extremely sensitive to very small changes with the haltech boost control.

I also believe the head doesnt flow enough for really big power figures. It is a Tomei Genesis stage 2 head. Supposidly good for a 2.8lt at 9000 RPM... I have 600cc more than that.

Nice work, so what's next for the motor?

Thats all for this one. It has achieved its goals as a monster of a street engine. It will just be external tweaks here, and then to put some KM on it.

Development will continue with this version of spacer plate/sleeve configuration in the next two engines.

Further to the power situation, I lowered the rev limit to 7500 RPM for this session, where it was 8100 for the last session. The power drop off is because the soft cut starts to happen at 7300. Trent wanted to rev it more because the engine certainly wanted to make more power, at least on the lower boost levels. The exhaust housing restriction only started to be evident at higher boost levels, but is also made look worse than it is by the soft cut.

I lowered the rev limit for 2 reasons. First twas that I can't think of why I would want to ever rev it that much, as below 7500 there are still two gear choices that throw you in the seat.

The second is that the Nitto H beams are using ARP2000 bolts, and I didn't want to go stressing it un-necessarilly. After all, it is a street engine still and I want it to last. At 8000 RPM this engine has the same piston acceleration speeds as an Rb26 at 10,000 RPM. And frankly most RB26's that rev like that don't tend to live very long.

The 383kw dyno sheet is of the 98 octane run. There were cleaner runs without that odd dip in the middle, but you get the general idea.

Hows it drive Ian?
We need driving feedback :)

Its MAD! Intoxicating to drive and not just from the alcohol. Its so tame to drive at low speeds, happily cruising at 1800 rpm in 6th, but its also making boost at that speed if you put your foot down. Anything over 3500 is rapid acceleration regardless of gear. Even rolling gently into the throttle in 2nd causes full traciton loss. Peak torque must be somewhere between 5000 at 6500, because the rate of rev change at this point becomes extremely quick. I've not been watching the tacho when driving it though.

I'll have to do a video at some stage of a drive. Shame there is no tracks up here and they cancelled the sprint series due to damage to the go-cart track. The only options are the training days and a go-woah event at the yearly car show. But construction of the Springmount Dragracing (Andra spec) drag strip will be finished soon. I'd like to be among the first street cars to claim a 10.

I must say that I love the smell of the E85 too, along with the note change of how the car sounds at idle now.

Back to video editing...

post-26553-0-46730000-1438598244_thumb.jpg

Edited by GTRNUR

Finished the video of the tuning that was completed last weekend:

I am considering options to solve the top end power drop off issue, and think that switching to an EFR 9180 could be the answer to gain that top end back not lose too much of the low end grunt.

For the moment there are a few minor changes and updates that need to be done, and then I need to get used to the car agian.

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yeah, the latter. No diff should have a centre replaced without checking clearances because its unlikely to be the same as whatever came out. Not that that stops most people just checking a new centre in
    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
×
×
  • Create New...