Jump to content
SAU Community

Rb34 / 24U (Rb26 + 800Cc) - Project RB high deck engine (and related builds)

GTRNUR
 Share

Recommended Posts

GTRNUR Grand Master

GTRNUR

Posted
  • Author
Posted (edited)

May take you up on that Mitch. Base on the youtube vids I've seen and the documentation it looks pretty straight forward. I'm just making up the external map and wideband interface looms now.

I can't imagine Haltech would have left any surprises for me. Out of the box it should control the fuel pump speed and send the correct TPS signals to the Attessa right? Ive seen lots of other people have issues with these two simple things... Edit: Other ecu's of course... Wolf/vipec etc...

Edited by GTRNUR
  • Replies 273
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

GTRNUR
GTRNUR

Quick Update. I finally got a weekend off work and was able to visit a Springmount Raceway, which is a new drag strip that was built and 1.5 hrs drive from Cairns. I only ended up doing two

GTRNUR
GTRNUR

There has been big developments with the project.  Towards the end of June I completed and delivered the rebuilt RB33.  It has been run a few times and initial indications are that it should perform v

GTRNUR
GTRNUR

Update Time! Its been a long road to get here, but I finally have some test results for the engine. Last weekend Trent Whyte and Gordon Leonard from Mercury Motorsports jumped on a flight to tune my

Posted Images

Mitchee Proficient

Mitchee

Posted
Posted

High/low fuel pump control is hard set at 5% throttle opening (from memory). The TPS follower for the ATTESA 100% works as per factory, as does the injection duty signal to the MFD.

The pre-loaded base map should be enough for you to get started with. Just make sure you load the calibration for your MAP sensor, set your TPS limits, enter your injector characteristics and deadtimes and away you go. Set base timing (i like to lock the CAS all the way clockwise) by enabling the ignition lock and adjusting the trigger angle. Dont forget to set the engine capacity, and if you're running an ethanol blend of fuel without a flex sensor, deduct ~33% from your injection flow rate to allow for the fuel density difference. :cheers:

GTRNUR Grand Master

GTRNUR

Posted
  • Author
Posted

Not necessary, it just connects to Inj1. The MFD does the rest.

If you were able to program up an 7th injector channel, it would need to be configured to have the same output pulse width as all the other injectors. Also, you would need to put a load on the output, or a pull up resistor to +12v so the MFD would be able to read the variable PWM square wave.

GTRNUR Grand Master

GTRNUR

Posted
  • Author
Posted

Sorry no dyno time yet.

The Haltech is in now. It idles and revs. Didn't get a chance to drive it anywhere though, nor do anything but do the basic setup on the weekend.

With any luck I can take a day or two off later this week and spend some time on the phone with Mitch.

AI tell me my surge tank is still 2+ weeks away as well.

  • 2 months later...
GTRNUR Grand Master

GTRNUR

Posted
  • Author
Posted

More changes are still in the works. I've replaced the entire fuel system again after being talked into going down the E85 flex fuel path. So bigger injectors, more pumps, bigger fuel lines, external surge tank and bags of fittings...

It takes for ever to get parts up here too. Pay for overnight and it arrives 3+ days later.

I've yet to source and wire in a flex fuel sensor, and I've got locate a fuel cooler to mount behind the diff too.

The interesting news is that I hope to be getting Mercury Motorsports to come to Cairns to do the final tune and setup of the car. If anyone can get it to produce a good final result, I think they are certainly capable of it.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • joshuaho96
      Rb25det Belts Change

      By joshuaho96 · Posted

      Everything I found online said never use it because it'll dramatically reduce belt lifespan.  No, but I have seen excessive v-belt tension cause the audible bearing noise from excessive radial load in things like alternators. So don't overdo it. Ideally you set it to manufacturer spec using a proper belt tension guage. I tried the "clicker" type gauges but those cheap things are trash. They read way too low even when you're careful.
    • joshuaho96
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By joshuaho96 · Posted

      This is kind of where I've ended up for the most part. It's easier for me, easier for shops that don't have to deal with my weird criteria/picky standards, etc.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      Will do. Suprised if it's not the starter motor considering it's 30 years old. Will get a volt meter though. Battery is close to new.   Cheers for your help, always appreciated.
    • GTSBoy
      Rb25det Belts Change

      By GTSBoy · Posted

      This almost never happens these days. No. Clean your battery terminals and make sure they are tight. Use sandpaper on a dowel if you have to, to get oxidation off the inside of the terminals, particularly on the -ve. Check the earth cable from battery post to chassis ground and engine ground. Make sure the contact surfaces are clean - including the threads on the bolts that anchor them - because that's where a lot of the contact occurs. Wire wheel on a drill is a good thing for this. Make sure the crimps on those cables are all sound. Assuming none of that causes an improvement: Check the battery voltage after it has been resting for a while. If it's at the lower end of the range, put it on charge for a while, then see if it will crank better.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      I just checked my belt, it wasn't super loose but I could bend it past 90 degrees a small amount so I tightened it up and for the first time ever my car didn't crank first time, had to crank it again lol. Don't know if that was because I tightened the belt or if it's my starter motor going out (been having slow starts for some time). Coulda also been when I was recording I didn't crank the key properly and it didn't save the recording lol.   Is that a thing if you overtighten a belt it struggles to start?
×
×
  • Create New...