Jump to content
SAU Community

Rb20 < Rb25 Turbo Upgrade


Leeroy94
 Share

Recommended Posts

As for the water line, i ended up loosening the turbo off the manifold studs to jiggle the turbo to get them in, from memory.

This is helpful for anyone fitting a stock turbo its easier to do when the turbo isn't tightened up against the manifold.

Spray the nuts and bolts with a penetrating lube like penetr8 or penetrene or something first to save heaps of hassle.

Should be doing this before pulling old nuts and bolts off anyway. If you break something its not likely you can fix it on your own.

Good luck you should be fine with the swap.

What is the condition of the RB25 turbo you are fitting? remember these are very old hardware now

Link to comment
Share on other sites

What is the condition of the RB25 turbo you are fitting? remember these are very old hardware now

Its a 45v4 turbo. The guy said it was from a R33 and that is was also never boosted past 10psi.

From what I can tell it has 1-2mm shaft play without oil. Is that bad?

Ive read that they have factory shaft play of up to 1mm so that when they heat up it still spins freely? Or is that false?

What else should I look for on the turbo to tell its condition, type?

Link to comment
Share on other sites

factory shouldn't have any play, the whole turbo will heat up pretty evenly so bearing tolerances shouldn't change much

1-2mm sounds about right for a 20 year old stocker. just throw it on and fingers crossed it doesn't blow smoke

Link to comment
Share on other sites

a tune would get you a bit more power but probably no more than say 10kw. it would be more responsive and better on fuel but it's up to you. Your set up is on about the limit of the stock ECU.

Actually I'm not sure about the RB20 ecu's so maybe ask someone else; but it's worth mentioning that an aftermarket ecu + tune will be minimum $1250

Link to comment
Share on other sites

Without tuning you will run into the same problems as anyone else winding up the boost on an RB20 would, just at lower boost levels. The factory maps are richer and more retarded up at the the high revs and high load regions than are good for making power. The RB25 turbo pushes a bit more air at any given boost level (or more to the point, the exhaust side flows more exhaust gas at any given boost level, reducing restriction on the engine which is what allows more air to flow at the same boost, if you know what I mean). So what that means is where things might start to get a bit black smokey on an RB20 turbo at 14 psi, you may reach that sort of flow at 12 or 13 psi.

In addition, you will possibly max out the injectors in a similarly early way. It isn't wise to wind up the boost without knowing the fuel pressure stays good at high load and revs and the injectors aren't bumping up against the 100% duty cycle region.

  • Like 1
Link to comment
Share on other sites

Also a little hurdle you will/may come across...

The stock 20 turbo comp housing has a nipple to read boost for the wastegate actuator. The 25 doesn't. You will need a nipple welded onto your I/C piping to complete the conversion completely.

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • So.... when I'm finally getting around to having my power steering leak sorted, now it looks like I've got the same issue most A/T Skylines are having. My A/T light will randomly come on and I'm stuck in 3rd gear until I turn the car off and on again. Only 3 weeks ago I did a complete transmission service: Oil flush + new gasket + new filter. This came out of nowhere!! It wasn't like the car was driven hard. I drove about 3 mins down the road to get fuel and boom!!!  Anyway, I have a few questions and hope you fine people can help me out here. All questions are in red. 1. The solenoids: I was looking at the parts catalogue in Amayama and I could only find the Solenoids as an assembly. https://www.amayama.com/en/part/nissan/319404ax05 I read in another thread that Solenoid A = 31940-4AX02 & Solenoid B = 31940-4AX05 but the Amayama product has only the code of B. Is this the right part? Can anyone who has done the Solenoid changes or seen them confirm if this is the complete set of A & B?   2. Gasket and Filter: I'm not going to try change the solenoids myself because it seems difficult to do in a home garage with just 2 jack stands. I plan to take it to a shop and get it changed. I was also going to buy the transmission sump gasket at the same time so I don't reuse the same gasket. Should I just use the existing gasket as it has only been on the car since OCT 19th? (~3 weeks) Should I be buying a brand-new gasket and a filter? Does this job involve taking the filter out?   Thanks in advance to everyone. It's hard to find a video of someone doing a solenoid change on a R34 so any help you can give answering my remaining questions would make me less stressed.
    • Yea - From what I have seen from the video, the car idles like any R34 lol 50PSI of fuel pressure is hardly super abnormal, the regulator is working because the pressure remains static when the throttle gets revved, i.e pressure remains the same when manifold vaccuum changes. Bigger pumps on stock rails always bumped the pressure in the rail without using an aftermarket regulator to change that. Do you know what your IAC is actually doing? Has there been any data showing the stepper motor % etc? There's no way your idle is actually moving around the way the cluster(s) are indicating. You would hear the difference with the engine RPM flying to 3k and 1k in mere seconds. I'd be checking the wiring to the tacho. What the tacho is telling you and what the engine/ecu is telling you are different things. I assume your ECU doesn't display the spike. So whatever is telling the tacho to be at X rpm is doing something weird. When the going gets insane, you're on the wrong path. You've ruled out plenty of things that are working correctly/aren't the issue. Your idle isn't doing what the tacho is indicating. You have two seperate issues, I don't think they are linked, and the idle seems reasonably okay unless it's stalling which.. well, it hasn't. Troubleshoot the stall if it occurs by figuring out what your IAC is doing vs what it is being told to do.
    • So awesome! I love the RB with the exhaust on display.
    • NO HITS PRICE DROP   ENGINE - $8.5k ONO TRANSMISSION - $1.8k ONO  
    • If it has had a code in the recent past, the code should still be there waiting to be read.
×
×
  • Create New...