Jump to content
SAU Community

Need A 4" Titanium V Band Flange

d-ranged

By d-ranged,
in Fabrication

 Share

Recommended Posts

d-ranged Enthusiast

d-ranged

Posted
Posted

Can anyone get hold of one of these. I am in the UK and cant find anyone that does them!

I need it to fit to my titanium exhaust as I have just fitted a single turbo and had a 4" downpipe made up thinking my exhaust was 4" all the way through but it expands to 4" from 3.5"

Any help would be massively appreciated as i am now stuck with a car I cant use :(

Link to comment
https://www.sau.com.au/forums/topic/435011-need-a-4-titanium-v-band-flange/
Share on other sites
GTRNUR Grand Master

GTRNUR

Posted
Posted

Or you could get a stainless clamp and have some rings laser cut from titanium plate. Then weld them on one at a time using a stainless flange to keep it straight while welding, and push the pipe through a tiny bit so the holes centre and line up.

d-ranged Enthusiast

d-ranged

Posted
  • Author
Posted

Or you could get a stainless clamp and have some rings laser cut from titanium plate. Then weld them on one at a time using a stainless flange to keep it straight while welding, and push the pipe through a tiny bit so the holes centre and line up.

Interesting idea but the problem is i have to take it to a shop to do it and not sure if they would do something like that or not...

d-ranged Enthusiast

d-ranged

Posted
  • Author
Posted

Can you find a machinist to make you one, the other half of what you have now?

I dont actually have a flange on the downpipe i was going to get a stainless steel 2 bolt flange made up and get that welded to the downpipe but then when i went to get a drawing of my exhaust flange made up i saw it was actually a 3.5" flange which expands into 4"

My exhaust is a custom made in japan job as well from an Auto Select car.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

If you can find some stainless that slides nicely into the 4 inch Ti and slot it then clamp, it will be fine. Motorbikes use slip fittings like that all the time. Probably not the best outcome for such an expensive system though.

I guess you want to ditch the 3.5 inch section? Probably best you measure the Ti also, as the Japanese like to use metric pipe usually.

d-ranged Enthusiast

d-ranged

Posted
  • Author
Posted

If you can find some stainless that slides nicely into the 4 inch Ti and slot it then clamp, it will be fine. Motorbikes use slip fittings like that all the time. Probably not the best outcome for such an expensive system though.

I guess you want to ditch the 3.5 inch section? Probably best you measure the Ti also, as the Japanese like to use metric pipe usually.

That is an idea, but would prefer it to be bolted or v-band. Even a 2 bolt flange would do me or a 4 bolt as long as i can get a stainless one too!

The guys who fabricated my downpipe built it on their R33 as they are quite far away from me, i sent them my turbo and manifold and they bolted it up to their car and did the work. They made the downpipe a bit longer just in case as they didnt have my exhaust. I think there is enough on there to cut the 3.5" section off my Ti exhaust and still get it bolted up...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Zabuza
      Need AC Compressor for R32

      By Zabuza · Posted

      I’m thinking that’s the route I’ll  go, thanks for the input!
    • carnoobb
      V35 Overheat + Coolant Boil & Overflow + Engine not Starting

      By carnoobb · Posted

      Hey all, my 2004 Nissan Skyline 350GT overheated the other day with coolant boiling and leaking out of the coolant reservoir when I was parking. So today, I started it up again just to see if it was a thermostat/head gasket issue. After about 20 mins of running, temps were normal again, no coolant was leaking out and the upper reservoir hose was warm but my engine suddenly cut off. I checked the oil dipstick and cap when it was running and there was no white foamy residue and the exhaust did not have white smoke. I tried starting up the car again but it would only crank, similar to when I had a camshaft sensor issue just that now there’s no check engine light on the dash. Any ideas? Unfortunately I don’t have an OBD2 that can read the Nissan's programme.
    • Papichulo96
      Rb head oil drain dimensions

      By Papichulo96 · Posted

      Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • GTSBoy
      Need AC Compressor for R32

      By GTSBoy · Posted

      The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Zabuza
      Need AC Compressor for R32

      By Zabuza · Posted

      Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
×
×
  • Create New...