Jump to content
SAU Community

Recommended Posts

The turbo (the actual compressor housing?) or the turbo wastegate actuator? You've said it's gone to the actuator as well as it going to the turbo..

Sorry I do mean actuator when I say that. The red hose is connected to actuator, if you look closely in the picture you can almost see it.

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

Possible that debris fell from somewhere and smashed the turbine. Perhaps the turbo was spun pretty hard then removed and sold to you, and you just got unlucky? Just change the turbo again. Get an R34 turbo if you can for a little upgrade ;):P.

Yeah I thought this too but it's happened 3 times, after everyone's opinions though I'll try a couple different things out when I'm changing over to the new (did you mean rb25 neo) turbo?

The line on the gauge you are talking about is halfway to full in positive pressure? If so from memory that seems about right

Perhaps there is to much heat in the exhaust side, maybe its running to rich?

Does it backfire, shoot flames or have poor fuel economy?

Edited by 89CAL

The line on the gauge you are talking about is halfway to full in positive pressure? If so from memory that seems about rightPerhaps there is to much heat in the exhaust side, maybe its running to rich?Does it backfire, shoot flames or have poor fuel economy?

Yeah man 3 quarters so inbetween positive 7 and half. Too much heat on the exhaust side does sound like a high possibility actually because I heard that those ceramic wheels don't handle too much heat very well... It does have pretty poor fuel economy, it back fires sometimes, I think it does run rich because when I bought it. It had an N/A manifold on it and the lines were blocked. But ecu and injectors were still turbo (the car is a factory gtst)

Did you use the same w/g actuator on all the turbos? could also be a boost leak too, if its leaking badly the w/g will not open when it should

The boost reading seems to be normal also and all turbos have had their own actuators!!

Point being if there is a boost leak, the waist gate actuator will keep closed and spin the turbo harder until it reaches normal boost level.

Ohh okay!! So a boost leak would just be from loose or split piping from any pipes on the turbo side??

Although it would be running awfully rich if it did, how has your fuel economy been?

Hmm well i get about 300kms to a tank give or take. Regardless of how the car is driven, and I've done and re done all of those pipes a few times now.. Is there a simple way to try and find a boost leak? Or shall I just change all the piping and all of the boots cause they're pretty old could be split or anything

First up, the point on the intercooler piping where the boost sense is taken from (red hose nipple) is on the wrong pipe. Sure, if nothing else is wrong, it will work there, but if you have one of a couple of other problems that position will make more trouble for the turbo. If, for example, you have a restrictive intercooler (or a rag in the intercooler as the classic line goes - but it does happen from time to time!) then you will be reading the boost pressure AFTER the restriction. So the turbo will be pumping to quite high pressure, but the engine and the wastegate only sees a lower pressure and everything seems normal - except you destroy ceramic wheels. Same sort of thing can happen with a boost leak although that will tend to be a problem regardless of where the tappnig is done.

And I would like to point out to people that it's not really heat that makes the turbines come apart or separate at the joint to the shaft. It's overspeed. If you're running retarded or otherwise hot in the exhaust side then the high temperatures will lead to high shaft speeds. So it is a little hard to say whether the chicken came before the egg or the other way around.

I would definitely do two things. I would fit another tapping point to the intercooler hot pipe and I would get a known good boost guage and hook it up to both of those tapping points (not at the same time, obviously) and see what the real boost is, and see if the dash gauge can be trusted.

Also, with respect to what boost the dash gauge is reading....+7 (hundred mm of Hg) is pretty close to 14 psi. Therefore the halfway line is 350 mmHg and is about 7 psi. If you are running halfway between those then you are up over 10 psi. That's high enough already - the car will likely be edging into R&R at that point. If the boost gauge can't be trusted, then your actual boost pressure is anyone's guess.

If the vacuum hose goes straight to actuator assuming the actuator is working then it shouldn't be boosting more then what it should. Its a simple analog pressure valve.

Those turbos re almost 20 years old with unknown conditions, not much of a point of buying them 2nd hand. Since you went through few its probably worth high flowing one of your dead turbos, you can then run what ever boost your engine and mods are happy with, for much better performance.

First up, the point on the intercooler piping where the boost sense is taken from (red hose nipple) is on the wrong pipe. Sure, if nothing else is wrong, it will work there, but if you have one of a couple of other problems that position will make more trouble for the turbo. If, for example, you have a restrictive intercooler (or a rag in the intercooler as the classic line goes - but it does happen from time to time!) then you will be reading the boost pressure AFTER the restriction. So the turbo will be pumping to quite high pressure, but the engine and the wastegate only sees a lower pressure and everything seems normal - except you destroy ceramic wheels. Same sort of thing can happen with a boost leak although that will tend to be a problem regardless of where the tappnig is done.

And I would like to point out to people that it's not really heat that makes the turbines come apart or separate at the joint to the shaft. It's overspeed. If you're running retarded or otherwise hot in the exhaust side then the high temperatures will lead to high shaft speeds. So it is a little hard to say whether the chicken came before the egg or the other way around.

I would definitely do two things. I would fit another tapping point to the intercooler hot pipe and I would get a known good boost guage and hook it up to both of those tapping points (not at the same time, obviously) and see what the real boost is, and see if the dash gauge can be trusted.

Also, with respect to what boost the dash gauge is reading....+7 (hundred mm of Hg) is pretty close to 14 psi. Therefore the halfway line is 350 mmHg and is about 7 psi. If you are running halfway between those then you are up over 10 psi. That's high enough already - the car will likely be edging into R&R at that point. If the boost gauge can't be trusted, then your actual boost pressure is anyone's guess.

Do you think oil starvation could be the problem???

If the vacuum hose goes straight to actuator assuming the actuator is working then it shouldn't be boosting more then what it should. Its a simple analog pressure valve.

Those turbos re almost 20 years old with unknown conditions, not much of a point of buying them 2nd hand. Since you went through few its probably worth high flowing one of your dead turbos, you can then run what ever boost your engine and mods are happy with, for much better performance.

Hi Stao.....read my post. There are ways it could happen. Anything that causes that signal to be lower (where it is sourced from) than the turbo's outlet pressure will permit it to work too hard.

Do you think oil starvation could be the problem???

Maybe....but what happens when you have that is that the turbo spins up and gets hot, then the bearings gall and sieze and the sudden shock would be what shakes the turbine loose. But I wouldn't expect the shaft to spin nicely afterwards, and it sounds like yours still have been.

Well, most of Skyline turbos that came in has no exhaust wheels. The way of how stock turbine shafts are made is by attaching a small section of the ceramic exhaust wheel into a steel shaft. Both elements has different expansion and retraction rates, and its always the section of attachment which breaks off at the ceramic end. The age and history of them probably don't help either, I won't be wasting money and time trailing 2nd hand turbos if its my car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm hoping I just don't have to do an engine rebuild NOW. Doesn't mean I won't do it at some point. I think a plus point is that the car presumably ran on or close to stock power nearly all it's life so far. Only the Owner I bought it from actually increased power with a standalone ECU and blew the OEM turbos. And after it got thee 2860s it wasn't driven an awful lot either.   That is what I meant. With the twins coming on so late (4500-5000rpm) I hope the rods won't want to exit the block prematurely. And it still being a 26 means the torque curve isn't gonna hike up all that much.   It didn't blow up on the dyno when they tuned it to 500ish crank. So I suppose it'll be okay for now. They did put a Tomei head gasket on first though which did not seal at all, and they redid it with a Cometic one. Which I hope won't be my water leak.   Mainly anything oil. So far all it has is the N1 pump, oil restrictor and a filter relocation kit with a cooler.
    • 15000? ish? Something like that anyway. It wasn;t so much a wear as a tear that then spread. Might have lasted a lot longer if not bothered by just one incident, whatever it was. I took a punt. They are really comfortable and do a good job of holding. My daughter HATED it when I first put them in, and probably still does now. She has sensory issues and hates the way they are all up your business. I'm 197cm and 95kg. Not fat or particularly wide, and the XL size seat is the rigth fit. If I was any fatter it would start to get too snug. Any skinnier and you'd possibly want the smaller width.
    • Mrs rs focus came factory with recaro cs  sportsters in it and they a pain in the ass to get in and out of with the really high bolsters, once you were in them they were one of the most comfortable seats I have ever sat in
    • The NA 2.5 has very little torque. You won't feel much. Those trannies are also a million years old now and it could well be f**ked. First generation electronically controlled autos will often refuse to kick down, ete, etc, depending on what's wrong with them.
    • Yes, but no but yes but no. Those "it's fine up to 500HP" rules and everything else like it were all determined back when the cars were 10 years old. As they are now 30 years old.....what do you reckon the chances of something shitting the bed are? I'd say they are much higher now than they used to be. You might be lucky. You might be unlucky. Spin the wheel and find out. Yeah, nah. It's actually exactly the opposite. Making boost early and having heaps of torque able to be generated right in the middle of the rev range will do more to damage an engine than having to rev it high to make the power. Think about the load on the conrods, bearings, etc, to make 400HP at 4000 rpm, vs 400 HP at 6500 rpm. So someone has already "let the Nissan out" which is how we describe the increased chance of a fiddled with engine to have had something done wrongly. Many more engines that have been opened die than stock ones do - even if you into consideration how they are treated wrt power levels and the like. Again, not saying that yours will definitely have been put back together by a moron. But the possibility does exist. It's still a lottery. Spin the wheel. What weakspots?
×
×
  • Create New...