Jump to content
SAU Community

Recommended Posts

So here's the deal guys.

I've got oil spraying out of my dipstick tube as well as pushing my dipstick out of the tube about 150mm each time.
so clearly im getting pressure in the crank case

but ive tried all i can think of now im out of options, so far ive:

-replaced the PCV valve with a new genuine unit from nissan.

-checked all breather hoses to make sure they weren't blocked.

-done a compression test to make sure i wasn't getting excessive blow by that was causing oil to spray out. (read 140psi across all cylinders)

now thats where ive hit a wall..... i cant think of anything else to check =\
any ideas?


appreciate any help...thanks.

Link to comment
https://www.sau.com.au/forums/topic/435182-oil-spraying-out-of-dipstick/
Share on other sites

just went and checked the rubber is pretty hard around the seal but its still fitting pretty firm

surely though that shouldnt justify oil spraying out of the tube right??

well damn i hope thats not the case.......

im not getting any smoke blowing out the exhaust so thats not looking likely in my case but i might still look into that if i cant get it sorted otherwise

Doing a comp test is all good & well for an N/A application, BUT, what's to say your rings are not responding when boost pressure is applied? The only way to truly cancel out your rings would be to do a cylinder leak down test.

I build, run & tune LARGE turbocharged stationary engines. I've encountered this issue before. Customer complained about an oil leak. Discovered to my surprise when going from idle to load @ about +10''Hg (max is 30Hg/14.7psi)) crankcase pressure was going from -.5'' H2O to +25'' H2O & popping both dipsticks along with twin fountains of oil till the rings responded at about +15''Hg then everything would settle down. This particular engine had issues rejecting heat through its heat exchangers, its dump radiators were too small & subsequently had alot of high jacket water temp shutdowns.

Piston rings hate heating up & cooling down. if the temps are high enough, over time, they start to lose their tension & don't respond very well to pressure changes.

Pressurizing your crankcase to the point of popping the dipstick out can only come from one place. The only other thing I can suggest as 'for the time being' fix is to get a little bit of heat shrink (for wiring), place it over the rubber, heat it & refit your dipstick to stop it popping out. Then just hope you don't start blowing out other seals!

I was just going to suggest a leak down test. :yes:

140psi compression test result isn't brilliant, especially if that was after cranking for a while. Do you have a catch can fitted?


I got similar problem whereby if I park my car on a hill it burns oil out the tail pipe...

Valve stem seals?

Doing a comp test is all good & well for an N/A application, BUT, what's to say your rings are not responding when boost pressure is applied? The only way to truly cancel out your rings would be to do a cylinder leak down test.

I build, run & tune LARGE turbocharged stationary engines. I've encountered this issue before. Customer complained about an oil leak. Discovered to my surprise when going from idle to load @ about +10''Hg (max is 30Hg/14.7psi)) crankcase pressure was going from -.5'' H2O to +25'' H2O & popping both dipsticks along with twin fountains of oil till the rings responded at about +15''Hg then everything would settle down. This particular engine had issues rejecting heat through its heat exchangers, its dump radiators were too small & subsequently had alot of high jacket water temp shutdowns.

Piston rings hate heating up & cooling down. if the temps are high enough, over time, they start to lose their tension & don't respond very well to pressure changes.

Pressurizing your crankcase to the point of popping the dipstick out can only come from one place. The only other thing I can suggest as 'for the time being' fix is to get a little bit of heat shrink (for wiring), place it over the rubber, heat it & refit your dipstick to stop it popping out. Then just hope you don't start blowing out other seals!

some really good info there thanks man

probably an easy fix there with a bit of heat shrink, but im not looking for a cheap fix here id rather get it sorted properly

and like you said id likely start popping seals lol....read up on another forum some guy just clamped the tube with a pair of vice grips :mellow:

looks like i should defiantly go ahead with a leak down test then and see how shes looking

I was just going to suggest a leak down test. :yes:

140psi compression test result isn't brilliant, especially if that was after cranking for a while. Do you have a catch can fitted?

Valve stem seals?

nah mate no catch can....... would be curious to see if im getting anything blowing out through the breathers as well as the dipstick now that you mention it

defiantly worth doing then if you think it will help
being that the breathers run back to the intake though wouldn't that cause a vacuum in the lines from the pcv valve and through the breathers though??
hence its at negative pressure anyways?.... thats just a guess


haha well lets just say
I've got a heavier foot than brian o'connor.... pretty hard

Antz. U thinking a vented can?

yup..would have to be...you could just stick little filters a top your cam cover vents , but this will most likely spray oil everywhere...

anyway, to keep it simple.. if can is vented, block pcv...if can plumbed back to intake, retain pcv...

i could tell you not to drive it so hard but you would probably laugh at me :P

If u need bud I can make u a vented can. But me thinks ur problem will be increased buy the -5s u just bought. Enjoy.

haha i know right.... thats why im tying to nut this out before i chuck em on

shit timing how it kinda came up the day i paid for them :glare: ...... lol

you do some fabrication work do you?

i actually do think i "might" have a catch can off my old 33 in the garage somewhere

ill have to have a look ....but otherwise ill get back to you about that one :)

A catch can won't really help, you'll only be increasing the size of your crankcase a little. If a leakdown test fails to show where the problem is, then testing on a dyno to actually measure the crankcase pressure is what will be needed.

In my previous post I mentioned a water column measurement: +25" H2O. This is only about 1 PSI. It was an 18 litre 6 cylinder. It didn't take much pressure to lift the dipsticks. Just letting you know even a little pressure loss can do big things.

When you do a leakdown test, try to test in KPA not PSI.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't do it if your gearbox box has already having syncro issues. The short hifter will put a greater load on them. If you must I remember Nismo did a shorter shifter, with the top part being physically shorter and the part that went into the gearbox was the same as stock. In saying that I've had a C's short shifter (I think) in mine for many years, which was given to me as the previous owner was not sympathetic to the gearbox. Thus forwarned I was careful and had to modify my normal changing style. You have to be super accurate with your clutch and shifts
    • Well, after a week of daily driving and having to crawl out between the wheel and the side intrusion bars. I got myself a quick release setup. I went with an NRG short hub and Quick Release with some cute heart cutouts on the pull tabs. Nice and matchy matchy with the rest of the interior accents I have going on.  The only downside is the total stack height even with the short adapter is longer than the old HKB boss kit. Luckily I had some adjustment left on the column so move the wheel away.
    • stock shifter with new bushes, springs and cup will improve it. Gktech do all the bits. The opinion as the years have gone on is the redline is not great in old gearboxes.
    • Hi all   what short shifter do you use on your skykine r34?   my synchronous does have a problem and i was getting huge delay and grinding sound between 2nd and 3rd, did put shockproof red heavy stuff and it is great now/ no issues   would in your view short shifter screw this up?   people seems to suggest/ use cube short shifter and there is standard and premium. Seen review of premium as much better and less play. Thoughts?
    • Yeah, there's a bit of a density and friability difference between pebbles and any of those other things. Silicone will definitely float in oil and so will be mobile enough to move around. Although, again, if it is upstream of the filter it really shouldn't go any further. I would only ever worry about silicone when it is in places downstream of the filter. Upstream of the pickup is a whole 'nother matter. We've all seen what that does. I have seen the most abominable crap settled out in industrial gearboxes, trunnion lube systems and the like, without any sign that any of it has touched anything in the machine. Just chilling in the bottom, waiting for the inevitable operator error that causes the whole machine to need to be dismantled for repairs.
×
×
  • Create New...