Jump to content
SAU Community

Recommended Posts

OP, if I was in your shoes, this is what I would do.

Seeing that it's a street car ONLY, leave the engine in, put 6-6.5 litres in the sump and drive it (middle of the hump). I don't believe it's cost effective to pull the engine, sump off, pump, baffles then put it back in. You've just done a half assed job. If you're going that far you may aswell spend the little extra and give it a freshen up (IE Ring's and bearings. While you're there pistons and rods... Very easily get out of hand). We are now talking about a rebuild.

If and when the time comes, then do all the above.

Well the engine is coming out regardless because I'm respraying the whole car a different colour including the engine bay, so I will speak to them about doing the rest of the work as well as it's out, it's going to make sense in the long run I guess.

Yeah I certainly wouldn't pull an engine out just to spray paint the bay especially if the engine doesnt NEED work

To do a good paint job it has to come out or it's all just going flake off I don't plan on painting it again, doing it all properly once.

Paint the car and do the engine bay when the motor lets go cause its going to happen soon enough lol I cant believe Croydon told you to pull the motor, put an oil pump and sump on it and leave the rest..... if your dead set on painting the whole car then get the motor rebuilt and do it all at once.

There is no reason that CRD should damage the engine bay, i dont recall destroying anyones freshly painted engine bays when i pulled motors on GTR's.... there is heaps of room to work with when you have done lots of them ;)

As for the sump and pump, CRD use Performance Metalcraft i am pretty sure so the sump will be an awesome bit of kit and you will end up with a NItto pump. Not entirely sure what they are like for longevity, i guess time will tell.

Paint the car and do the engine bay when the motor lets go cause its going to happen soon enough lol I cant believe Croydon told you to pull the motor, put an oil pump and sump on it and leave the rest..... if your dead set on painting the whole car then get the motor rebuilt and do it all at once.

There is no reason that CRD should damage the engine bay, i dont recall destroying anyones freshly painted engine bays when i pulled motors on GTR's.... there is heaps of room to work with when you have done lots of them ;)

As for the sump and pump, CRD use Performance Metalcraft i am pretty sure so the sump will be an awesome bit of kit and you will end up with a NItto pump. Not entirely sure what they are like for longevity, i guess time will tell.

Ok so new plan, respray car blue as it gun metal grey at the moment, and leave the engine bay the colour it is unless masking everything up will look ok

OP, if I was in your shoes, this is what I would do.

Seeing that it's a street car ONLY, leave the engine in, put 6-6.5 litres in the sump and drive it (middle of the hump). I don't believe it's cost effective to pull the engine, sump off, pump, baffles then put it back in. You've just done a half assed job. If you're going that far you may aswell spend the little extra and give it a freshen up (IE Ring's and bearings. While you're there pistons and rods... Very easily get out of hand). We are now talking about a rebuild.

If and when the time comes, then do all the above.

Perfectly said.

Forget all this $1700 sump, $1500 oil pump business... It's just not required.

Overfill the stock sump by 1ltr, drive around fine. Sumps, extensions etc, you'll never need them at that power level and use.

Perfectly said.

Forget all this $1700 sump, $1500 oil pump business... It's just not required.

Overfill the stock sump by 1ltr, drive around fine. Sumps, extensions etc, you'll never need them at that power level and use.

Ok cheers guys really appreciate the advice and money your saving me at the moment lol!

What colour is engine bay now, I have blue Gtr and bay is black from factory .. Just curious

It's also black but it has so many scratches on it just looks horrible, guess I could re black but thought it would look nicer in blue.

post-125705-13856224438374_thumb.jpg

Not sure the photo really shows how crap it looks!

post-125705-13856226037551_thumb.jpg

And this doesn't show how faded the paint is due to the water being on it!

post-125705-1385622508991_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...