Jump to content
SAU Community

Recommended Posts

Depends on what one you get. I have not dealt with them personally but many people here swear by Hypergear. Where is kasko or Troy when you need them.......

haha!

with a turbo upgrade will injectors need to be done to?

Power?

What about suspension?

And a good diff isnt cheap. You cant use the power if you dont have a good diff.

Fix all the shtty bits first, then youll be broke again.

But your car will be reliable.

And yeah its:

turbo, boost controller, fuel pump, injectors (no rail or fpr needed), exhaust, Pod & cold air box, Nistune ecu. And a tune up.

Not cheap.

Did you fix that timing belt?

Its all for nothing if that belt goes.

Dont worry about shiny bits just yet.

post-89755-0-08082400-1385714793_thumb.jpg

Edited by D.I.Y. Mik

what sort of power increases will you see?

250rwkw is fairly common with the highflows. Though lately I've been seeing a lot of 270+ results, some even reaching 300+ on e85 with stock internals. As Anthony has already stated you will need supporting mods to achieve this :)

Depends on what one you get. I have not dealt with them personally but many people here swear by Hypergear. Where is kasko or Troy when you need them.......

I was getting drunk haha

Ello ello

Hypergears new high flow is his best turbo and its only $850 and should net you around 250-260kw

I'm running an SS1PU version and making 250kw but that's on 20psi.

You will need all the supporting mods though which adds up after a while.

-ECU

-AFM

-Fuel pump

-injectors

-metal intake

-boost controller

-boost gauge

-intercooler

-exhaust

And a tune

Sortout your suspension and alignment first. I your struggling to put down 150-170kw no point getting 250kw. i have 210rwkw atm and I can drive flatout without spining the wheels on average tires. I recommend front castor arms rear camber arms and a good alignment i run my alignment close to SKs specs but with slighlty more camber.

sweet thanks guys, nah im starting to think its not the timing belt, thinking its a pully that's out of line or to tight... I really hope its not the timing belt!

It is the timing belt.

sweet thanks guys, nah im starting to think its not the timing belt, thinking its a pully that's out of line or to tight... I really hope its not the timing belt!

Yeah, a timing belt idler or the tensioner.

Stop thinking about it and have a look before it breaks.

I got gates belt on and its to tight makes a noise when idling,

Also i just bought a plazmaman plenum and now i have to relocate the AAC somewhere and get the car tuned

if anyone had done a plazmaman plenum and relocated the AAC a help wound be good

It sounds like a Gates belt wound up too tight.

Yeah, a timing belt idler or the tensioner.

Stop thinking about it and have a look before it breaks.

both guys that have hurd the sound both agree with the timing belt, time to start saving.. so awkered dropping my mate off at formal just before with it fuly detailed and having that sound... it spun into second just before, if that says iits standed power or not..

its a bad feeling going to the formal of your school and not being able to attened :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Do the R32s run high or low impedance injectors?
    • It may not feel like it to your wallet....but sounds like this was one of those "lucky you did it" rebuilds. Hopefully you have better luck this time
    • It's aftermarket. It also reeks of Honda Civic tryhard from 2003. But if you want one....then you want one.
    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
×
×
  • Create New...