Jump to content
SAU Community

M35 - Engine Light On

cabbie_bro

By cabbie_bro,
in Four Door Family & Wagoneers

 Share

Recommended Posts

cabbie_bro Enthusiast

cabbie_bro

Posted
  • Author
Posted

Auto Electrician rang to ask where diagnostic port is.

Can anyone tell me where exactly the port is on a NM35 Stagea?

I just said "have you looked around the driver n passenger foot wells?"

Brick Mentor

Brick

Posted
Posted

Auto Electrician rang to ask where diagnostic port is.

Can anyone tell me where exactly the port is on a NM35 Stagea?

I just said "have you looked around the driver n passenger foot wells?"

Might be time for a new auto electrician.

Brick Mentor

Brick

Posted
Posted

That's what I was thinking. Lol. They come highly recommended around town and alot of business gave em a good wrap. Probably just lazy to look.

Hopefully your right.

But as pn-mad said it is driver side.

cabbie_bro Enthusiast

cabbie_bro

Posted
  • Author
Posted

They reckon they have found a loom of wiring that is corroded really bad near the location of the battery with water pooling. They cutting it out now and going to replace that section and going to keep the old section to show me.

Daleo Grand Master

Daleo

Posted
Posted

They reckon they have found a loom of wiring that is corroded really bad near the location of the battery with water pooling. They cutting it out now and going to replace that section and going to keep the old section to show me.

There have been a couple of these lately; it might be worth everyone checking.

A stitch in time; saves nine. ;)

PN-Mad Grand Master

PN-Mad

Posted
Posted

Yup, turn car off remove key, open the fuse box in the drivers side footwell, and stick your hand down there as far as you can. See if you can feel water, or moisture. That will mess up your electrics real quick. I make a habit of clearing the crud from the plenum area, right down to where the drains are in the bottom of the guards. Mud and crud build up over time.

cabbie_bro Enthusiast

cabbie_bro

Posted
  • Author
Posted

Got the Stagea back from the Auto-Elec yesterday, a big chunk of wiring loom got replaced and everything is running sweet once again.

Taken it for a few drives with no problem.

So great warning for people, make sure you clean out your drainage points regularly because its not worth the problems if you don't.

Daleo Grand Master

Daleo

Posted
Posted

Got the Stagea back from the Auto-Elec yesterday, a big chunk of wiring loom got replaced and everything is running sweet once again.

Taken it for a few drives with no problem.

So great warning for people, make sure you clean out your drainage points regularly because its not worth the problems if you don't.

Good to hear it's sorted, definitely a timely reminder for everyone else.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • r32-25t
      R32 Gtr Long Term Love, Now Project

      By r32-25t · Posted

      to fix the voltage drop issue I swapped out the old 150amp alternator which turns out is a brand known for having issues and replaced it with the black 180amp alternator beside it 
    • S1_C34
      A31 Digital Climate Control

      By S1_C34 · Posted

      For anyone interested, the Way Back Machine has that Japanese website archived with pictures, etc: https://web.archive.org/web/20051023225805fw_/http://www.a31cefiro.com/air_con.htm "Simply swapping the wiring of the harness will not allow it to function properly. For the outdoor air sensor and sunlight sensor, disconnect the wiring connected to CN1-11 of the air conditioning harness from the harness and connect the sensor side wiring to earth. For the indoor air sensor, disconnect the wiring connected to CN2-3 of the air conditioning harness from the harness and connect the sensor side wiring to earth. The connector PIN numbers listed here are the genuine A31 PIN numbers. To avoid incorrect wiring, check with a tester before wiring. Also, disconnect the wiring in a location close to the sensor. The disconnected harness side wiring will not be used, so be sure to insulate it." Wish someone sold a conversion harness to just plug-and-play a Kouki 180sx digital climate control into C33/A31. I'm decent with wiring but feeling kinda lazy about taking this on. Edit: Did some more digging and found a helpful Minkara blog post about the conversion as well: https://minkara.carview.co.jp/userid/1831116/car/1360568/2284209/note.aspx "After installation is complete or the battery is replaced, you need to go into self-diagnosis mode and set the internal air recirculation. The way to do it is to "hold OFF with the key on for more than 5 seconds, set the number to 5, then press 卍→C." ↑↑↑It probably won't make sense unless you actually try it (・∀・)." Lol wtf
    • MBS206
      Skid pans in/around Sydney?

      By MBS206 · Posted

      Maybe SAUNSW could see howany members would do a motorkhana day if Schofield's is still available for a reasonable price...
    • MBS206
      Skid pans in/around Sydney?

      By MBS206 · Posted

      Skip the concrete, we just need to smooth a field. Mark knows how to drive a grader Duncan   I reckon 100x100 flat area for skid pan style, and then some sort tracks for rally... Duncan's already got a rally car on the premises to...
    • GTSBoy
      PRP RB26 cast block + head prototype running

      By GTSBoy · Posted

      Well, yeah, the RB26 is definitely that far off the mark. From a pure technology point of view it is closer to the engines of the 60s than it is to the engines of the last 10 years. There is absolutely nothing special about an RB26 that wasn't present in engines going all the way back to the 60s, except probably the four valve head. The bottom end is just bog standard Japanese stuff. The head is nothing special. Celicas in the 70s were the same thing, in 4cyl 2 valve form. The ITBs are nothing special when you consider that the same Celicas had twin Solexes on them, and so had throttle plates in the exact same place. There's no variable valve timing, no variable inlet manifold, which even other RBs had either before the 26 came out or shortly afterward. The ECU is pretty rude and crude. The only things it has going for it are that the physical structure was pretty bloody tough for a mass produced engine, the twin-turbos and ITBs made for a bit of uniqueness against the competition (and even Toyota were ahead on the twin turbs thing, weren't they?) and the electronic controls and measuring devices (ie, AFMs, CAS, etc) were good enough to make it run well. Oh, and it sounds better than almost anything else, ever. The VR38 is absolutely halfway between the RB generation and the current generation, so it definitely has a massive increase in the sophistication of the electronics, allowing for a lot more dynamic optimisation of mapping. Then there's things like metal treatments and other coatings on things, adoption of variable cam stuff, and a bunch of other little improvements that mean it has to be a better thing than the RB26. But I otherwise agree with you that it is approximately the same thing as a 26. But, skip forward another 10 years from that engine and then the things that I mentioned in previous post come out to play. High compression, massively sophisticated computers, direct injection, clever measuring sensors, etc etc. They are the real difference between trying to make big power with a 26 and trying to make big power with a S/B50/54 (or whatever the preferred BMW engine of the week is).
×
×
  • Create New...