Jump to content
SAU Community

Recommended Posts

Selling my Original Speedy Spyders (rare not made anymore)

18 x 8.5" Rims with dish and offset to suit Skylines, Silvias and Fords
A small amount of gutter rash, small flat spot inside left front rim, however you cant notice it even at speed, and some small chips on the rim (fixable)(see pic) which was made by the shop who installed my new tyres..

Ive owned the rims for 6-7 years, and they have been really good. cost me $1,500 back then. They are currently on the car and to prove the condition they

will be on the car this weekend at the track.

These are a pretty decent mid range rim, not the lightest but they are strong.

Will remove once buyer has made downpayment

Asking: $400 ono

Price is for rims only, no tyres. however I can add a set of Potenza RE 050A street tyres 75% tread for an extra 250$

rhc8.th.jpg

0mwh.th.jpg

=====================================================================================

600 x 300 x 76 KLS Japan Alloy Intercooler

Type: Bar and Plate

Condition: used this for about 5 years, still in very good condition

item is clean and sealed ready to go.

will suit almost any vehicle

Asking: $100

ir3e.th.jpg

====================================================================

RB30 S2 Engine

I have a RB30 S2 Engine here, including head

everything good on this motor except for the crank.

$300 for the lot

50qq.th.jpg

==================================================================
RB25 Head ready for 30/25 conversion
Fully prepped 25 head
Crack tested head.
Boss welded and tapped for side VCT Feed
VCT Feed on port face welded and head decked
Full valve job, all new Vavle stem seals
all relevant welsh plugs welded, and head cleaned and checked.
comes with stock cams and lifters
$2k + worth of work . receipts available.
asking $750 ono

3e51.th.jpg[/u

RL]

=================================================================

R33 Skyline Cam and Valley Covers (RB25)

Asking: $150

As you can see, full set of RB25 Covers Wrinkle painted, and valley cover meshed. (same head as above for sale)

28m8.th.jpg

==================================================================
Jim Berry Single plate 6 puck carbotic clutch with balanced billet flywheel
700hp rated
asking $200

40416310150994016341534.th.jpg

==================================================================
K&N Pod (cost $160)
Still really good condition only used for about 5k kms.

Asking: $30

knfilteri.th.jpg

==================================================================
2.5 Tonne Workshop Jack
6 years old, really reliable strong, cost $260 new
selling for $120
nothing wrong with it, just need a slimline one.

pc6g.JPG

==================================================================
Stock R33 GTST Swaybars

Front and Rear good condition with rubbers 50 bucks for both.

stock33swaybar.th.jpg

==================================================================
stock R33 GTST Cams

I dunno?... $40 no scoring, ready to go.

[url=http://imageshack.us/photo/my-images/145/rb25detcams.jpg/]rb25detcams.th.jpg

All reasonable offers considered.

Call or SMS 0432279166

  • 2 weeks later...
  • 1 month later...
  • 2 months later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For sure the later RB26 variants had a different setup (6 cam voltage sender?), but the RB25DE/DET share the same ECU pinout/PCB footprint, and at the ECU plug it ends up being 'throttle sensor in' & 'throttle sensor out' (to A/T TCU) ...you stick a multimeter on these pins and you'll find them directly connected (0 ohms) ; I had an pair of Nissan ECUs on the bench long ago, and I noticed this throttle sensor in/out link, actually linked to an op-amp ...which was unpopulated on the NA board, but present on the T board and I went 'ah-ha!' in some moment of clarity... ...it wouldn't surprise me if they changed strategy here though (in the software and actual monitoring of this signal), because they did with other stuff (A/T signals).. and 0.45v as a trigger point makes sense, as that's what the external TCU units expect at idle ; kudos, thanks for that insight...I suppose it boils down to whether or not Consult can display real time data of that signal's voltage... ...in any event, it presents the same target...ie; rotate TPS unit to achieve 0.45v to suit both ECU&TCU, and where do you goto from there? Just disconnect TPSwitch connector and/or that plus TPSensor connector....or do you go for the throat and disconnect IACV solenoid and see if it still stalls? (probably throws a recoverable fault code and goes for default idle strategy?)...
    • I’m also conscious that e85 is slowly being phased out. Not all United’s have them anymore. Can’t take the risk of being low on petrol and assuming the servo will have it. 
    • MR HAMMER has said his piece. Painted up to avoid Rusty Rusty. Actually lines up well. (i.e it lines up the same as the unmolested GTR guard). Turns out the GTR Strut brace does foul on the bonnet vents ever so slightly. May need a little bendy bendy if intended to keep using with a strut brace. So spacing it out to clear the FAST102 is not an option. Annoyingly, the bonnet vents also foul on the heater lines running over the engine. Given this engine does not EVER require a heater, a delete loop is going to be used. Don't worry, the defogger uses the AC. The heater is basically "Do not use the aircon and turn the fan on". It will still be effective, I promise.... once I get the system regassed... Will have to revisit with unvented bonnet I suppose, and suitable strut brace. There's plans to do this and other things tonight and bleed brakes (there was a weep) and put the bumper back on, and take Good Friday morning - Because troubleshooting on the side of the road limping it home at midnight tonight is ... not very smart.
    • Thank you all for you assistance. I contacted Nistune regarding the support for the RB20DE along with my ECU Code (23710-10U00). They do have a map for it and added the RB20DE as a purchasable option now as well. They also added Malta as a Billing and Delivery options as this was missing. I was honestly amazed at their quick response and action, it took less than 24 hours. I also looked again at direct fit options for injectors, just in case I were to replace them. DeatschWerks seem to use a Bosch EV14 base and makes ones that fit mine at 440cc lowest, but also have 550cc at the same price. I tried looking for other direct fit options and managed to find one (also Bosch EV14 based) which includes a plug and play adapter on ebay. Did a small test with a Noid Light on the troubled injectors and all seems good, so they are pulsing properly electrically. One weird part is that they are missing on the same two cylinders as before I got the injectors cleaned. Mechanic also found this weird as he did not label the injectors and it is unlikely to have the faulty injectors be installed in the same cylinders.  
×
×
  • Create New...