Jump to content
SAU Community

Recommended Posts

Hey everyone,

I had to take my front right wheel off to send it in for repairs as it is a little bit damaged and my car is currently sitting jacked up in the garage.
How long is it safe for to leave it jacked up for? (using the standard skyline jack)

Thankyou! Any comments are greatly appreciated

Link to comment
https://www.sau.com.au/forums/topic/435961-r33-car-jack-concerns/
Share on other sites

If you have another rim/tyre sitting around that can be bolted on, bolt it on. If it can't be bolted on but you have a spare, throw it under the sill of the car, at least then the car has something to land on when the jack fails.

unless its old and rusty and also that you have not jacked it up crooked then it will be fine.

Just don't lean on the car or bang it with those little jacks as they can bend at the feet n the jack collapse bringing the whole car come down...

Should never jack up a car and leave it on the jack

A set of axle stands are cheap and may save your life

yeah I should have qualified my above statement with don't be getting underneath it with those jacks, nor letting kids around it.

I honestly swear I have never gotten under the car with just jacks.... :whistling:

yep. and the silly thing is we do it knowing this.

I wont be doing it again after last year seeing a car come off its jacks. thankfully nobody underneath and wheels were still on too, so no harm done. just a good lesson.

Seen plenty of cars come off jacks, had my own do it before too, ive also watched a scissor jack turn into a giant banana when a car was up on one, and fell off it while a bolt was being undone in the engine bay. Jack became completely useless... Luckily no one was under it.

  • Like 1

every year people are crushed/killed working under their cars when it falls off the jack

this happened to me last year when the metal jack mount under the car bent (minus the me being crushed to death part). Had some serious pant-soilage when the car dropped and I heard the clang as the jackstand took the load.....gtfo from under the car in record time lol

^^ I can relate to that

Had a car come off the jack and because id been too lazy/stupid to put axle stands under it the car nearly got me

Youd be surprised how quick a fat guy can move out of the way when a car drops down for a "hug"

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...