Jump to content
SAU Community

Recommended Posts

ok, where do i start

got an r33 gtst, last week on my way to work I pulled into the servo and there noticed when I turned off my engine smoke was coming from my engine bay. let it sit for 5 then when it subsided opened it up to try find the source. nothing appeared to be coming from leads, turbo etc (that I could see).

got under the car and noticed the smoke was pouring out from the bell housing (just incase where motor n box meet) didn't see it dropping oil/ has never dropped oil.

oil was full when I left that morning and check it it again at the servo, fine as chips wasn't milky or watery. after letting it sit for 10 mins, smoking stopped and decided to drive it again.

Get 2 mins up the road and I can slightly hear mayb bearing crunching or something like it, definitely coming from either right side or dead under. Car looses power on acceleration up the hill and completely stops.

after waiting about half hr, car decided to start again enough for me to move it into the car park opposite. by this time it has a really loud know in the engine bay, if I had to guess id say coming from bottom of motor.

during the whole time the car never overheated and unfortunately I was paying attention to the oil pressure so not sure if that dropped or not.

after about 4 hrs when I came back to tow, the knock in engine stopped, couldn't hear the bearings crunching when I drove it onto the trailer and there was a small puddle of oil (im assuming) noticed from a far so could have been box fluid.

I haven't driven it since so wouldn't know if its still doing it, not keen to risk further damage.

any ideas what this could be?. or how to start pin pointing things with out ripping the box out.

a friend- mechanic said it could be the rear main seal gasket, how do I check?

Link to comment
https://www.sau.com.au/forums/topic/436202-r33-fkd-transmission-any-ideas/
Share on other sites

stopped driving it as soon as it was off the road, towed to mechanic who has no idea.

yes auto. his suggestion was to pull the motor out n go over it all.

its getting the conversion after xmas so if it has something to do with the transmission its not gunna matter.

What does the auto fluid smell like?

A sweetish smell & red in colour, or burnt smelling & blackish in colour?

Any visual signs of leakage when underneath it?

When was the engine last serviced & what type of oil?

If it spat big end bearings in the engine it would have rattled when you loaded the engine to get it on the trailer.

Without being there to check it out, I'd recommend removing gearbox, drain engine sump into a container & check oil in sunlight for metal, fresh oil & filter & then start the engine up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm firmly on the "zero compliance is good compliance" for FUCAs. I'd be looking to solid metal joints even if the primary reason for having them is because they facilitate the twist in the arm. I have never been more happy with the way the front suspension behaves than I have since I got rid of the FUCA bushes. Even the thin little (short lived) poly bushes in the Whiteline adjustables have too much compliance for my liking. It probably won't be long before I have sphericals nearly everywhere, probably including both top and bottom arms in the rear, and I'll start complaining about the increased costs for dental work. But I will be enjoying the driving more, I'm sure.
    • Plus, you'll get great experience in bedding in pads!
    • I have offset Nismo brackets so the fact the gktechs can pivot is less important to me. I have 170mm JIC arms with bushings - but they provide no adjustment and I'm not sure whiteline eccentric bushings will fit them (I don't want to ruin the bushings currently in them to find out). Ideally I want something with bushings + adjustment; hence why I'd like to find a pair of these. Unfortunately they aren't easy to find.
    • @Vee37 How much do you really care about finding these pads again? If your pads are quiet, work well and produce minimal dust, really isn't that enough? If you are set on finding the exact pads again, I suppose I'd do something like this -  Visit your local Jax, find out what brand of pads they carry. If the Jax workshop you previously went to had the pads on the shelf, then you can almost guarantee it will be of said brand.   I'm guessing you don't have the receipt for the previous work and pads. Can you visit a Jax workshop and see if they can look up your previous job to see what pads were fitted?  Still no luck? Put your stalker hat on, find the staff that used to work at the Jax store and ask them. Talk to local workshops, try to find out where the mechanics went to. Talk to Jax workshops, maybe they relocated to another workshop. When it comes to mechanics, its a small world. You'd be surprised how easy it is to track someone down. If these ideas don't work, shit will start getting crazy very quickly.... You could find out every brand and model of pad that fits that car... and try them individually ticking each off the list if it wasn't the one you were looking for.... If you go down this path your going to want to learn how to swap pads yourself, it is very easy, takes minimal tools and space. If you have room to park the car you have room to swap the pads. Plus you have the advantage of making sure all the brake hardware goes back in so they won't squeal! 
    • You miss spelled bearings...
×
×
  • Create New...