Jump to content
SAU Community

Recommended Posts

I have a stepper boost gauge which is powered by an accessory circuit. When starting the engine, the gauge switches off and on again. The problem is I think the gauge has a self zeroing startup procedure, ie it centres the dial to 0 boost/vac. When it turns on the second time I believe its zeroing to about 0.1 bar boost (that is what it ends up on when turning the engine off, back to accessory position without disrupting power to the gauge)

Could a large capacitor be used to keep the gauge running in the short time while cranking the engine?

Think you have another problem. It should be designed to get around this.

The fact is that the starter draws alot of current, which drops your voltage. Dont think a Capacitor setup would be efficent or cheap enough for keeping a boot gauge on. Have you sourced power from a strange spot?

If your battery is dropping to much further then 9V during start then you might have another issue. And to me, 9V shoudl keep the gauge on.

FYI, I have an electronic boost gauge, electronic oil pressure gauge and an electronic Wideband gauge. All 3 of them dont drop out during engine cranking. I'd say the power source for your gauge is either from a bad spot, there is a problem with the earth, or the car is drawing to much power during cranking.

Like I said the gauges are (or should be) made to get around situations like engine cranking. I'd find it very unusual for the gauge to require a capacitor/reserve power supply to keep it powered during cranking

Maybe a silly question but does it matter?

what is critical or failure if the vehicles voltage to the meters turns off during cranking? especially if it is ancillary (eg: radio)

defi gauges do this in the evo VIII, i'm not sure what the issue or seriousness is

in the evo they power up when the key is turned, then off whilst cranking and then on when running.

so my questions are out of interest

Edited by Sinista32
  • 1 year later...

So just to revisit this, I had further problems with the gauge and voltage drop during cranking. Perhaps my battery is getting close to replacement time (voltage drops to 10 around cranking).

Anyhow I thought I would test out some of these Chinese supercapacitors that have been popping up on ebay at a decent price.

Basically I connected 6x 2.7v 6F caps in series to produce a 16.2v 1F cap bank. These were about the size of AA batteries.

Coupled with a 6 amp diode, I produced a circuit similar to this: http://en.wikipedia.org/wiki/Reservoir_capacitor

Only difference being the source is DC in a car, not AC.

It works a treat, and not only smooths out the voltage supplied to any connected load, it also helps to reduce transient voltage drops.

This is being used to power my innovate wideband controller (3 amp draw on start due to the heater), plus my gauge. I would probably use larger capacitors if I made one again.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Interesting, I've heard complete opposite on my end. Bit of a lottery I guess.
    • Getting Dangerously close to being ready to go back in the car. Rockers in with clearance castings now (and a quick check with the USA for the torque settings for the larger custom bolts) Covers and ported FAST Manifold sitting on there. Not fully tightened down as there's some clearancing required for the water pump with the earlier LS1 water pump styles. Example of the clearancing needing to be done: The body has to be ground a little but I'm struggling finding an actual piece of it. The later variant of water pump resolves the issue as the manifold was designed around it. It only came on the VZ LS1 in Australia, it got a different pulley for Gen4 motors. (it also costs $450... vs... $0).
    • https://files.fm/f/5atwkuvcjd
    • Doing some height adjustment on front suspension on a v35 and noticed this. The passenger side looks correct. So wondering what's happened to the drivers side?
    • Oh...I have the electric mirrors as well iirc ...they're in the same state as just about every other R31 door mirrors, with the 3 plastic screw towers broken/cracked in the plastic molding. All the interior is 'dry', so the mirror switches etc likely all work fine. Some pics below of the trimmer pieces ~ looks to me like previous owner, painted chrome finished trims with black paint ...ergo, the chrome underneath is likely a-ok... ...starts to look yukky posting stuff like this, how much did it cost in fuel on your last sortie up this way?...me just thinking aloud, borrow someone else's 4cyl to cut costs, come do your own pick'n'pull like before to save me some bother...hehe.. but whatever, I'll just earmark bits I know you want, because the way this is all panning out, I'll be able to retire the R31 from daily duty at long last, replacing it with a Subaru wagon I'm lining up in the wings...ergo, my attitude towards the donor pinny shell is starting to wane a bit, and I'm more than happy to help you out there... Like you say though, no rush...and I'll guarantee we won't be moving too far from this locale at any rate 😎
×
×
  • Create New...