Jump to content
SAU Community

Recommended Posts

hey there,

my series 1 stagea is sitting at stock height and has 18inch wheels.... i noticed it has the floating feel when driving, the rear tends to float over bumps and gives the feeling that its following any grooves or bumps or ditches in the road... i had similar thing in the past with my commodore wagon and a hilux but am told its because they are light in the rear end...

is there anything i can do to try and sort the issue, i do not want to put coilovers in can't afford and i dont want to lower...

First thing to look at would be your rear dampers. If they're old/worn-out then they will definitely make the rear end feel floaty. If they check out to be good, then the next step would be to inspect the UCA and LCA bushes. After 15 years the stock items will be on their way out.

It is a wagon after all, and is built with a large empty box at the back. On my old worn set of tyres, getting down to a quarter tank of fuel was like an arcade drift game...

something other than worn tires is causing that.

thanks for the info, its had an alignment and is on brand new tyres...not sure of profile size, i will get the dampers and bushes checked out this week.......as for replacement ones if it is the scenario what kind of price range would i be looking at?

you dont need to lower your car, a stock high ride height is fine and shouldnt feel dangerous.

take it to pedders or somewhere that will do a full check testing shocks and componants.

theywill try and sell you everyting pedders under the sun but just get the check done and go from there.

Just my 2c, when I had a pedders 28 point inspection, they missed everything wrong with the suspension. When I paid $120 for a reputable workshop to do an inspection they came up with a very very thorough list (also more than the suspension). Most opinions on pedders are about as flattering.

*** However, I should add that I did not agree with everything on the comprehensive list. I also made more cost effective repairs eg, the workshop wanted to replace the entire strut and spring assembly just to replace the shock. I replaced the shocks myself.

I guess my experience was almost the opposite. I knew something (or several things) was wrong in the suspension and pedders didn't pick up on them. - as opposed to workshops usually racking up unnecessary repairs.

yeah get what your saying zoomzoom... i would go tomorrow and buy a set of coilovers if i could believe me and i think if our 2nd child wasn't so close to due date i would... but it sucks the floating when i am driving on my own in car but once there is a little weight from family being car its almost non existent.... and i can't really lower the car at the moment with my wife so close u know

Lowering the car isn't going to make any difference. Stock height is not causing the problem.

Yes it does , lowering the car puts constant pressure on the strut and pre- loads the suspension , its a short term cheap fix without replacing stock struts .

Like i said , this fixed my problem and very well .

Now i run Bilstiens with Tein lowering springs actually works better for street ride and will outlast any coilover .

Then again coilovers might be your best option to keep stock ride height ?

Bad advice going to pedders ……...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hmm. Yes. I should have been clearer. 1000s for Haltech, for extra headroom. 725s for Nistune. You might even be OK with 640s, but if the possible power ends up much more than 300 rwkW you will run out of headroom on the 640s. That would probably be OK and a signal to not push it to that sort of power with Nistune anyway. At that level you probably do want to be thinking about engine protection functions. Oh, and all of that presumes 98 only, not E85. Well....the 1000s would allow you to run E85 at ~300rwkW territory, again, maybe sort of running out of headroom. Hard to tell with E85 - depends on the tuner as to how rich they like to set it up.
    • Yes.  The only scenario I can imagine when the answer isn't yes, is if you drive like there is highway patrol behind you at all times.  If your car currently runs, enjoy it and keep saving. Better costs more, keep saving until you can budget the better ECU. It's worth it.  Nope. Plenty of us making >300kw on unopened motors. Mine is unopened and makes about 350kw if I turn everything up, its fine (lots of caveats here, how the car will be used/abused, how long you expect the engine to last between rebuilds, how has the engine been maintained prior to coming into your ownership, etc etc).   
    • Sorry just wanting to clarify, at this power goal, which should I be going? Also, More info regarding suspension, the rear upper camber arms were used to get the camber back to i believe around -0.5 ~ -1 degree (@ Road and Race in Rydalmere), I forgot the exact figure, but ALOT less camber than what it came originally which was like -2.5degrees. Are the traction arms still recommended? The bilsteins from SydneyKid, they've got 400lb/in fronts & 275/in in the rear, revalved to his specs. Intercooler, I'm just having a look at some on Rakuten.jp and some other japanese sites. Might get something from back there, GReddy, Blitz or HPI, all crossflow. Looking at roughly $450-$500 AUD + shipping... Theres not many choices except that chinese branded Justjap unless you go for blitz return flow. Yeah, only downside with Haltech is the price ahhaha, so expensive, and with all the sensors if I go that route... $$$$$ yeesh. Are headstuds/gaskets needed for <300akw?
    • Haltech fanboi reporting in. Buy the Haltech! 
    • You can try shoving a borescope down there to see what's up.
×
×
  • Create New...