Jump to content
SAU Community

Recommended Posts

This is surplus to my needs, the delivery of my Avalon unit was actually much earlier than thought

The BFL unit literally arrived yesterday, BRAND NEW! Works perfectly

A solid 30Gh/s of power - Simple to use, plug 'n' play with your mining software of choice

$1100 delivered or best offer!!!!

post-1182-0-40527100-1389237167_thumb.jpg

post-1182-0-18820600-1389237180_thumb.jpg

The quick version - You get rewarded in BTC for supplying the network with CPU power to confirm the monetary exchanges and transactions. The more power you can supply, the bigger the reward.

The BTC you earn, you have transferred to a monetary exchange in Australia that will credit your bank account in dollars, I use www.coinjar.com and withdraw the cash daily, current exchange rate is ~$1000 per BTC

It's a little speculative investment and lots of fun!

What's the payback like?

How long to earn a whole bitcoin?

How much electricity does it use per bitcoin?

EDIT: Actually, if you had one in your house today, it may pay itself off in a few weeks but in 24 months the cost of the power used to mine would be greater than the BC you get in return, so there's money to be made on one for the next couple of years.

Edited by Cowboy1600

What's the best price you'll do on the 50, taking into account it's old tech and you can get a 2x25s for ~$1600 brand new from Butterfly labs - they are ready to ship.

$1600 brand new from Butterfly labs - they are ready to ship......

Check out their shipping costs ;) Then add import duty, GST and the fact that "ready to ship" means........."ready to get the parts off the shelf and build you a bitcoin miner as we don't actually hold stock and make to order"

Dealing with BFL and ordering means you actually get your order 1+ months later

Not being funny at all, but they are very strange in the way they operate.....I can 1000% promise ANYONE that I'd have a brand new 200Gh/s miner in their hands in 2 weeks, BFL can't

I'll do $2000 flat, delivered for the 50Gh/s unit, which should be at least 55Gh/s going by most of the averages I'm seeing from these.

Edited by 666DAN

There wouldn't be any duties, etc, cause I'd get one and I'd get a mate to get one ;) that brings em in at under a gorilla each :)

But $2k ain't bad. I have a little co-op together and I think we're keen. We can't figure out if it'll ever pay itself off or not, but for $500 each we're willing to give it a bash.

I'll be in touch.

BOTH SOLD!

I can get a brand spanking new ASIC 200GH/s Avalon for $4500 if anyone is keen, limit of TWO at this price and only available for the next few days. They land in under two weeks and don't have an owner. Check ebay, second hand ones start at $4000 and go for way more!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...