Jump to content
SAU Community

Recommended Posts

All items from my personal GTR 32. Located in Melbourne.

Air conditioner cooling unit - $220

Heating unit assembly - $240
Complete blower motor and fan assembly. Working well. - $150
Transfer case originally from R33 GTR - $220
Rear seat (back and bottom). Excellent condition - $120
Cusco strut tower bars suit R32 Front and rear. Avg condition. Scratches and paint chips - $180 pair
Weather strip retainers (L&R). Poor condition rubber strips, both suit restoring. Metal guides are excellent condition - $40 pair
Rear wiper motor - $90
GTR floor mats. Complete set. Avg condition, usual wear, no holes - $140 set
Interior carpet. Good condition. No stains, no burns. 2 small cuts for harness bolts - $120
Air con compressor, bracket, gas cylinder, and hose - $130

CUSCO springs (from Zero 2E coliovers) Cusco ID65 200 series. Spring rate: 11kg, Inner spring diameter: 65mm, Length: 200mm, Stroke: 100mm. Travelled 2000kms - $120 pair
GTR 32 front grill (silver) Good condition. Centre plastic clip missing - $110
Interior rear side trims (L&R) Excellent condition. All clips in tact, no tears in vinyl - $80 pair
Factory gauges for boost, water temp, battery. Fits into single din slot. Comes with loom plug - $110
Rear seat belts. Excellent condition. Barely used. Belts retracted into spool. Comes with fitting bolts - $100 pair
Climate control head unit. Good condition. All buttons work. Comes with loom plug - $90
Top cowl cover Fits under front wipers. Excellent condition, no damage - $40
Complete heater / AC ducting. Full kit includes behind dash and under carpet ducts - $30 set
Rear window lower outer moulding. No damage - $35
Rubber weather shields (L&R). Heavily worn but still working - $30 pair
Front door outside moulds (L&R). Poor condition. Suit painting - $40 pair
A-pillar trims (L&R) 3 small holes in drivers side for pod gauge fitting - $40 pair
Rear parcel shelf (original). Good condition - $40
Original Nissan brake lines and used Bendix pads - $40
Nissan standard CAM gears - $40
Oil catch can. Never used. Looks about the size of 500ml - $20
Rear seat firewall plate. Avg condition. Some scratches - $35
RB26DETT oil air breathers and joins - $20
Antenna booster - 12V amplified New. Boosts weak FM radio signal (10dB gain). Problem particular to R32's where the antenna is built into the windscreen - $20
Under bonnet trim Avg condition. No damage, just needs a clean - $20
Sun visors (L&R) Avg condition. Need a clean - $25 pair
Boot trim, carpet, and board Good condition. Left side trim torn slightly. Holes cut in side trims for struct tower bar. Selling as set - $25 set
Rear window wiper -$20
Nissan spare jack (original) - $15
Child anchor points and brackets Fitted onto rear parcel shelf during compliance process - $15
Interior roof lining. Excellent condition. No damage - $20
Pics available for all items..
Link to comment
https://www.sau.com.au/forums/topic/437715-random-parts-r32-gtr/
Share on other sites

  • 2 months later...

Hi just wondering if you are able to ship the rear windscreen moulding?

If you are referring to the rubber moulds, these are heavily worn. If you are talking about the hard plastic moulds, then yes I can post within Aust.

Allow $15 for postage

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan! Yeah it's street use for me only. Maybe occasional track day. Any difference in noise when running with the two pumps? I would expect the lift pump to be more quiet than the main pump so hopefully not? And yes, unfortunately quite a big price difference to the simple hanger setup. Though I'm usually willing to trade money for better reliability and future-proofing. Buy once, cry once and all that. I'd be very happy to never have to deal with fuel pump / wiring issues again  
    • The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
×
×
  • Create New...