Jump to content
SAU Community

Recommended Posts

Hei guys

Realized my stagea's speedo is reading wrong but some margin. Its showing more than im actually traveling, know that traffic is usually slower than the speed limit and even when i was driving 10 over there would still be cars passing by so I took this GPS unit to check it as they are supposed to be accurate and speedo is actually showing more than gps unit. Its like 10 over at 60 and almost 20 over at 100. When speedo is showing 120 GPS says im traveling at some 100-103 kmh...

So was wondering has anyone had similar problem or is this not that common, what causes it and yeah most important how to fix it.

Link to comment
https://www.sau.com.au/forums/topic/437745-calibrating-speedo/
Share on other sites

I don't have stock wheels and tyres, but they are about the standard diameter and my speedo was also reading about 10% over.

I put on of these in the car (tapped in near the dash): http://www.jaycar.com.au/productView.asp?ID=KC5435

BTW ADRs specify a speedo must be between 0 and 10% over actual speed....how crap is that?!?

M35's are notorious for the speedo reading high, I run 235/45/18's and they still read 10k's over at 100. I hoped the Nismo cluster would be more accurate, but it wasn't.

The ecu is reading the correct speed according to my informeter, but the speedo is still out, so I just use the informeter for accurate speed measuring.

I don't have stock wheels and tyres, but they are about the standard diameter and my speedo was also reading about 10% over.

I put on of these in the car (tapped in near the dash): http://www.jaycar.com.au/productView.asp?ID=KC5435

BTW ADRs specify a speedo must be between 0 and 10% over actual speed....how crap is that?!?

Hey Duncan, was it difficult to splice in & get accurate?

My speedo is approximately 10% out as well, which is a PITA for me, with 110kph limited factory cruise control :(

My ARX runs 225/55/18 as per the placard and when the spedo is at 110 the car is actually doing 103 (per my GPS)

The V36 is out by about the same. I reckon they are built like this to slow people down.

Now I figure if i run 245 45 18 as suggested above, this will reduce my rolling diameter from 2214mm down to 2129mm and throw the spedo out by another 4 kms/hour.

I figure that if I were to run 235 55 18 then at 110 on the spedo the car would be going around 105 kms an hour.

Found some Dunlop SP Sport 235/55/18 100V LM703 for a reasonable price. Anybody running these?

245 55 18 would produce about 107 kmh at 110, an error of only 3kmh but this tyre size is likely an off road tyre and if it didn't touch my plastic guards would sound like a truck anyway!

My ARX runs 225/55/18 as per the placard and when the spedo is at 110 the car is actually doing 103 (per my GPS)

The V36 is out by about the same. I reckon they are built like this to slow people down.

Now I figure if i run 245 45 18 as suggested above, this will reduce my rolling diameter from 2214mm down to 2129mm and throw the spedo out by another 4 kms/hour.

I figure that if I were to run 235 55 18 then at 110 on the spedo the car would be going around 105 kms an hour.

Found some Dunlop SP Sport 235/55/18 100V LM703 for a reasonable price. Anybody running these?

245 55 18 would produce about 107 kmh at 110, an error of only 3kmh but this tyre size is likely an off road tyre and if it didn't touch my plastic guards would sound like a truck anyway!

You're right Chris, the tyre set up I have suggested won't solve the issue on an AR-X, as they run a larger rolling dia than the RS/RX/AXIS. Do they use a different Speedo cluster?

Using a tyre size guide, should allow you to plug in easily available tyre dimensions, and reduce the error.

Blek it was pretty straightforward to install, the wiring is actually marked on the rear of the cluster so I just intercepted the signal on the way into the dash. AFAIK in most of these cars the signal goes from gearbox to dash and then everywhere else (eg ECU and cruise control) so the dash is a good place to intercept.

The only thing to be aware of is that the link I posted is a kit, so you will need a soldering iron and some patience to put it together.

I'd normally prefer to just change tyre size (am doing that in the leaf ATM to fix the same issue) but that's expensive if you aren't already due for new tyres anyway.

You're right Chris, the tyre set up I have suggested won't solve the issue on an AR-X, as they run a larger rolling dia than the RS/RX/AXIS. Do they use a different Speedo cluster?

Using a tyre size guide, should allow you to plug in easily available tyre dimensions, and reduce the error.

I have a feeling that the cluster may be different.

when I've seen Nismo clusters on Yahoo, if I remember correctly, they state NOT ARX.

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeah i agree paint match stops it from standing out so much, oh that's actually really good to know i was wondering if it would help with air flow now actually having an outlet in the bonnet. Will have to focus on ducting into and out of the radiator now to make the most of it.
    • I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
×
×
  • Create New...