Jump to content
SAU Community

Tein Control Master Type Flex Coilovers + Edfc Control Unit - Bcnr33/bnr34

Blitz
 Share

Recommended Posts

Blitz Grand Master

Blitz

Posted
Posted

Hi all,

Due to a setup change on my R33 GTR, I have for sale my excellent condition set of Genuine Tein Control Master Type Flex Coilovers, complete with the Tein EDFC (Electronic Damping Force Controller)

These coilovers are top shelf quality and manufactured in Japan, not China, and are suitable for BCNR33 and will also fit BNR34

All 4 are in outstanding condition, and have seen very little use overall - My car came with this setup fitted and in as new condition, and has since covered around 3,000 km's only.

Spring rates are 8kg (F) 7kg ® from memory, and provide a great range of adjustment to make them firm yet comfortable for everyday driving, while also being excellent on the track.

The EDFC gives you the ability to quickly and easily adjust the damper settings on the fly, from inside the cabin.

post-46-0-52704500-1390022125_thumb.jpg

post-46-0-84975600-1390022143_thumb.jpg

post-46-0-80248300-1390022153_thumb.jpg

Technical Information from Tein:

TEIN has used its years of experience in various motor sports to produce a kit that provides the ultimate balance between comfort and performance. Developed for drivers seeking an aggressive coilover that can be used daily, and provide all the adjustments needed for circuit use. The FLEX damper Kit features the latest technology for all drivers who are seeking performance, and adjustability, while not giving up all ride comfort. We have incorporated separate spring perch height, and shell case length adjustment, which allows the suspension to retain more stroke and allows for more suspension tuning. The FLEX damper kit includes pillow ball upper mounts, which increase steering response; 16 levels of damping force adjustment, and is compatible with the EDFC (Electronic Damping Force Controller) for added convenience and adjustability.

Standard Features:

• Steel Construction
• Twin Tube internal construction
• Ride Height adjustable via threaded body and spring seats
• 16 way adjustable dampers, compression and rebound combined
• Pillow ball upper mounts for increased steering feel
• Upper camber adjustment on front for strut type vehicles
• Larger piston diameter for strut type front and rear (22mm)
• EDFC (Electronic Damping Force Controller) compatible
• Powder coated brackets with Teflon coated shock body for heavy duty rust prevention

Per the Tein USA Official website, the Control Master Type Flex base kit will set you back around $3000USD, and that does not the EDFC, which will add another $400 or so.

I am asking $980.00 firm for the whole kit - Note this is DIRT cheap, so please don't haggle or try low balling.

Pickup available on the North Shore in Sydney, or alternatively you are welcome to organise your own courier to pick up.

First in, best dressed!

Cheers :)

NYTSKY Grand Master

NYTSKY

Posted
Posted

I have had these coilovers in my car for 6 years and feel exactly the same today as they did back then.

Quality product!

Blitz Grand Master

Blitz

Posted
  • Author
Posted

Not at this stage sorry mate, I would prefer to sell the EDFC and suspension as a package.

Price drop to $900.00 FIRM!

Blitz Grand Master

Blitz

Posted
  • Author
Posted

As above, and per the photos, they are in excellent condition and were only removed due to a complete change in my setup, so there is no need to rebuild.

This is a high end Japanese coil over package that I'm selling at a dirt cheap price purely to move them, it's a damn good suspension setup for minimal money, so my loss will be someone else's gain here.

Cheers!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I mean I can be OCD'y but this is really over the top. At that point why not just run a full wideband fuel controller? Especially if you run 3 widebands. The system works pretty well, which is trimming low load stuff to be within a few percent of the base map. Pre-engine _change_ the base map was only 1-2% off, depending on ambient temp, elevation, etc. Under load the LS is really very straightforward to tune, enough that a wideband closed loop would be overkill. If I really cared (and I hope I don't) I can always just go back to the MAF system the car actually came with. Which does all those nice calculations for me (temp, altitude, etc), now that you can buy 102mm MAF's that do not cause restrictions.
    • Pac
      Who has a Infiniti Q60, Q50 (V37)?

      By Pac · Posted

      Good afternoon Team , just a quick update on performance mods  Current Mods list (Installed) HKS - Power Editor (Came with the car) looks to be some kind of boost controller RV37 Skyline 400R (SKYLINE) | FUJITSUBO  - Cat Back  RV37 Skyline 400R (SKYLINE) | FUJITSUBO  - Front Pipe AMS  - INFINITI Q50/Q60 RED ALPHA COLD AIR INTAKE KIT AMS  - Performance Heat Exchanger Intercooler Not Yet AMS Alpha Performance Full Race Down Pipes  - to be installed in May 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I'd be installing 2x widebands and using the NB simulation outputs to the ECU.
    • GTSBoy
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By GTSBoy · Posted

      Nah, it's different across different engines and as the years went on. R32 era RB20, and hence also RB26, the TPS SWITCH is the idle command. The variable resistor is only for the TCU, as you say. On R33 era RB25 and onwards (but probably not RB26, as they still used the same basic ECU from the R32 era), the idle command is a voltage output of close to 0.45V from the variable resistor.
    • dbm7
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By dbm7 · Posted

      It's actually one of the worst bits of Nissan nomenclature (also compounded by wiring diagrams when the TCU is incorporated in ECU, or, ECU has a passthru to a standalone TCU).... the gripe ~ they call it the TPS, but with an A/T it's actually a combined unit ...TPS (throttle position switch) + TPS (throttle position sensor).... ..by the looks of it (and considering car is A/T) you have this unit... https://www.amayama.com/en/part/nissan/2262002u11 The connector on the flying lead coming out of the unit, is the TPS (throttle position sensor) ...only the TCU reads this. The connector on the unit body, is the TPS (throttle position switch) ...ECU reads this. It has 3 possible values -- throttle closed (idle control contact), open (both contacts open, ECU controls engine...'run' mode), and WOT (full throttle contact closed, ECU changes mapping). When the throttle is closed (idle control contact), this activates what the patent describes as the 'anti stall system' ~ this has the ECU keep the engine at idling speed, regardless of additional load/variances (alternator load mostly, along with engine temp), and drives the IACV solenoid with PWM signal to adjust the idle air admittance to do this. This is actually a specific ECCS software mode, that only gets utilized when the idle control contact is closed. When you rotate the TPS unit as shown, you're opening the idle control contact, which puts ECCS into 'run' mode (no idle control), which obviously is a non-sequitur without the engine started/running ; if the buzzing is coming from the IACV solenoid, then likely ECCS is freaking out, and trying to raise engine rpm 'any way it can'...so it's likely pulling the valve wide open....this is prolly what's going on there. The signal from the connector on the flying lead coming out of the unit (for the TCU), should be around 0.4volts with the throttle closed (idle position) ~ although this does effect low throttle shift points if set wrong, the primary purpose here is to tell TCU engine is at idle (no throttle demand), and in response lower the A/T line pressure ... this is often described as how much 'creep' you get with shifter in D at idle. The way the TPS unit is setup (physically), ensures the idle control contact closes with a high margin on the TPSensor signal wire, so you can rotate the unit on the adjustment slots, to achieve 0.4v whilst knowing the idle control contact is definitely closed. The IACV solenoid is powered by battery voltage via a fuse, and ground switched (PWM) by the ECU. When I check them, I typically remove the harness plug, feed the solenoid battery voltage and switch it to ground via a 5watt bulb test probe ; thing should click wide open, and idle rpm should increase... ...that said though, if it starts & idles with the TPS unit disconnected, and it still stalls when it gets up to operating temperature, it won't be the IACV because it's unused, which would infer something else is winking out...  
×
×
  • Create New...