Jump to content
SAU Community

Recommended Posts

A few shitty cars like Mazda 3s, Honda Civics.. mainly just stupid P platers

Been tailgated, slammed brakes really hard.. no more tailgating :)

Then they overtake me and abuse me, so I follow their car with a creepy smile on around till they start speeding and driving erratically.

I've followed some dumb betch home before and abused the shit out of her till she started crying. Then I said I hope you've learnt your lesson and apologised for making her cry and left.

I'm a dickhead.

  • Like 4

One serious case was i accidentally drove into a dead end construction site road at night time in Bankstown and this riced up P plate Honda Accord with big guys in it blocking off the only exit so i slowly and carefully squeeze past them and they said "Who you looking for ?" to which i said no one and sped out of that dead end then they chased me around Bankstown very closely (can't see their headlights), i had to block their lane so they cannot get in front of me as they try to overtake me to do god knows what, they even sped past a red light to chase me, i lost them by going around and around at the round about then parked in front of the Bankstown Police Station.

Bankstown is dangerous at night time and Skylines have too much negative attention.

happens all too much, usually by middle age people (say 40-50) in 4x4's that have never been off the road.

bloody tough waste of space morons!

I hit the brakes a few times to flash my lights at them, if they don't back off I then slow down and try to box them in traffic just to really piss them off. =)

  • Like 1

Single road situation, I am usually a tad over speed and if they persist I just slow down until they get the message and move back, works most of the time but sometimes it just makes things worse if you have a nutter up your butt :rant: then it is time to GO or pull over :blush:

I have a thing about young sheilas doing it and as soon as you go to a bendy part of the road the fall way back only to sit up your butt again on the straights :stupid:

A lot of the time people who get tailgated deserve it. The driving culture in Perth (where I am) especially is ridiculous. People sit in the right lane on the freeway either just doing the speed limit or a bit below and then have a little sook when someone comes too close behind them and high beam them. Here's an idea, bugger off out of the right lane sparky and you won't get tail gated.

But offcourse you do have those idiots who will tailgate you irrespectively so yeah....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...