Jump to content
SAU Community

SAU 3rd Annual Putty Road Cruise and Lunchon, Sunday 4/7/04


Recommended Posts

  • Replies 350
  • Created
  • Last Reply

Top Posters In This Topic

Will be attending this event:

  • SW20-GT
  • Majanal & Jody
  • CS_180 (did you get an engine?)
  • Biatch (Duncan)
  • Kel
  • Shell & Damo?
  • Moanie
  • Abo Bob & My Girl (Bobsgirl)
  • Endorean
  • Neil & Mel
  • Unregistered (Is this a real person?)
  • smileyr33
  • MRK-25T
  • mattR33
  • 2rismo & Taryn
  • Aurora & Amaru
  • Craved & MR2 + 2 more
  • PranK & Bec?
  • Blitz + 1
  • R33vit & Wife (Barbara)
  • BOO57A
  • Ash + 1 or 2
  • mchaplin
  • Jimbo & Lindi
  • JAS-25t & Amanda
  • Supra + 1
  • GTR032
  • DrewR33GTR (Come and meet the crew drew!)

That is 40 confirmed and 13 maybe's!

Maybe's

  • YRL05S
  • Sidewaysmambo
  • decow
  • NYL83R
  • shonen
  • B-man
  • Ed
  • benm

Guys, I a bit worried that the putty rd might not be able to handle all the traffic, so I'm going to cut it off at 30 people... sorry to all those that were so keen for this... just not too sure if the road can take it is all, that and the traffic jam getting out of Macca's!

JOKES!!!!

Should be huge... can't wait. Don't forget to fill your forms out early and have a quick read of the supp regs during that boring friday arvo meeting! Oh, and bring a pen and your CB on the day.

Someone asked what the cost of Lunch was, I can't remember off hand, but I think $50 should cover your meal and a drink or 2. If you want to find out you can call the imperial hotel on 02 6572 1290. If you need to contact me then I'm on 0414 195 896.

Cheers,

Dan.

After Lunch it will be up to you all what you do. I will be going to sample a few of the local fermented grape juices and perhaps some old mouldy dairy products. All are welcome to tag along.

Barb and I would really like to join you...

Anyone else wanna go wine sampling??

Hi Marjanal, i'm keen for the cruise. Can i join SAU on the day?

Yes mate, sure can... either print one out (in my sig below) to do before hand or fill it out on the day. ;)

And yeah, I was joking... sorry bout that, sometimes I just can't help myself!

OK Tosh, Kel, Sam and Barb we have accom for Sunday night.

I tried Peppers so we could crash Adrian's romantic weekend :cheers: but they didn't have cheap.

Cypress Lakes on the other hand did, so we have a 3 room villa there for $60ea.

http://www.cypresslakes.com.au/default.asp...=article&ID=337




  • Similar Content

  • Latest Posts

    • I’m thinking that’s the route I’ll  go, thanks for the input!
    • Hey all, my 2004 Nissan Skyline 350GT overheated the other day with coolant boiling and leaking out of the coolant reservoir when I was parking. So today, I started it up again just to see if it was a thermostat/head gasket issue. After about 20 mins of running, temps were normal again, no coolant was leaking out and the upper reservoir hose was warm but my engine suddenly cut off. I checked the oil dipstick and cap when it was running and there was no white foamy residue and the exhaust did not have white smoke. I tried starting up the car again but it would only crank, similar to when I had a camshaft sensor issue just that now there’s no check engine light on the dash. Any ideas? Unfortunately I don’t have an OBD2 that can read the Nissan's programme.
    • Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
×
×
  • Create New...