Jump to content
SAU Community

Recommended Posts

Very nice. Do you have much problem with rust over there, with all the snow?

Thanks :) Snow isnt the problem, but salt used to keep ice out of the road is.. But here in northern Finland they doesnt use it so much :)

^^^ Looks awesome!

I just can't get over seeing an R34 against the quintessential Finnish backdrop ... it's a loooong way from Yokohama :)

Thanks :) Yeah, its isnt the usual backdrop :D

Thanks :) Snow isnt the problem, but salt used to keep ice out of the road is.. But here in northern Finland they doesnt use it so much :)

Yeh that's what I was getting at; I had a look under my Opa's car in Germany once. 1997 Audi S4, had so much rust underneath it made me nervous getting in it. Still, beats sliding off the road because they didn't salt it!

Yeh that's what I was getting at; I had a look under my Opa's car in Germany once. 1997 Audi S4, had so much rust underneath it made me nervous getting in it. Still, beats sliding off the road because they didn't salt it!

Haha :D Luckily i dont drive my r34 at winter. I dont care if my bmw get some rust :D

Looks good.

Front bar is a bit too solid for me.

The division between lip and bar actually helps.

Also with the side all closed up :P

Thanks!

You mean holes in stock gtr lip? I think theres no big benefit of those if you dont have air ducts installed :)

Edited by Guula

Hi Markus,

Love your work. I like the body kit work you have done.

Also appreciated the fact you seem to be majority of the work yourself.

The R34 looks nice smooth. Bet you she loves the cold too ;)

I miss Finland very much and have even been contemplating relocating there, and if do I would take my R32 GTR with me.

Will keep an eye out on this thread.

Top stuff

Hi Markus,

Love your work. I like the body kit work you have done.

Also appreciated the fact you seem to be majority of the work yourself.

The R34 looks nice smooth. Bet you she loves the cold too ;)

I miss Finland very much and have even been contemplating relocating there, and if do I would take my R32 GTR with me.

Will keep an eye out on this thread.

Top stuff

Thanks mate! :)

recon you should shave the door handles !

My friend said the same :D But im not going to go there now, maybe later if repaint the car etc..

I just drove little 1300km road trip and next thing is raise the boost 0.7 -> 1.2-1.3 and tune it :) Turbo and new screamer are awesome!

  • 4 weeks later...

Like to see a DIY on making that front lip?

I have to check how much i have photos of making it :)

How did you go, any dyno results yet?

Hope to get it tuned next week.

My clutch release bearing started to make some noise so had to repair it week ago.

Also replaced all bushes from rear. Much more solid rear now :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
    • ...oops. forgot the TCU end...
    • No I got mine from a friend that had fabricated one … but I had to fit it to my setup which was a hks turbo setup. His was a Garrett -7. So one of my turbos was not a flange for one side … then I had a leak in the welds I had to find a weld shut … in the end the setup was decent priced but I spent a lot to get it fitted. A couple companies I checked would make it but you’re talking 7-9k aud with titanium. No joke mine was 6-7k even second hand after I had to fit it in Hong Kong … labour is expensive here. 
    • I'd just like to restate that I don't think anyone here is actually hating I recently sold a car part to a guy who was building a forged auto R34, with MV stall and aiming at ~450kw. I told him that I'm him, from the future and to stop after it explodes once. I told him I knew he won't listen the first time, and that's fine. But if my predictions do come true - Change direction faster than I did. I also said it's probably no coincidence that the dyno plot of a reliable turbo engine starts to look a lot like a N/A motor. :p
×
×
  • Create New...