Jump to content
SAU Community

Recommended Posts

Selling for my boss. Up for sale is his 1996 R33 Nissan Skyline. It's a 2.5L NA 4WD 4 door auto and completely original. It's been sitting in a paddock for a few years and so the paint needs a good cut and polish. It was imported from Japan in 2002 with just over 100k on the clock, with a Nissan 100k service sticker to verify this.
When the car was imported it ran perfectly with no dramas at all.
Currently the car turns over but won't start because one two wire connector on top of the engine seams to have been bitten by a rabbit. However this seams to be the only damage of the sort and is in a very easily accessible location.
The interior is in very good condition aside from the occasional spider..
Exterior has some wear and tear, small dint on front of bonnet, front bar paint is cracking slightly and other slight signs of wear as you can see in the photos. Patch of rust appearing on right rear corner of bumper and scuff on righthand sideskirt.
Reason for selling is that it's taking up space and I need to move it on. Unfortunately it cannot be registered because it's power to weight ratio is not great enough to classify for the Register of Specialist and Enthusiast Vehicles.
If interested feel free to contact Dave on 0412 316 011 for any questions or offers. I'm not looking for much for it, but at the same time I don't want to give it away. Feel free to make me an offer

post-86575-0-55580000-1393889748_thumb.jpg

post-86575-0-03253100-1393889770_thumb.jpg

post-86575-0-55956000-1393889793_thumb.jpg

post-86575-0-42546000-1393889815_thumb.jpg

post-86575-0-97472600-1393889834_thumb.jpg

post-86575-0-94900900-1393889858_thumb.jpg

post-86575-0-38384500-1393889881_thumb.jpg

post-86575-0-93489700-1393889894_thumb.jpg

post-86575-0-26796400-1393889920_thumb.jpg

post-86575-0-82726400-1393889936_thumb.jpg

post-86575-0-70847900-1393889955_thumb.jpg

post-86575-0-25353100-1393889966_thumb.jpg

post-86575-0-31432200-1393889982_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/440045-1996-r33-gts-4-rb25de-for-sale/
Share on other sites

wow.... thats going to be a tough sale.....

na/auto/4 door puts it about 3k.

not being able to register it, is almost scrap value...

good luck with it man. rb26 + gtr box, this thing would fly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
    • Kinda something I have been thinking about.  To be honest, we bought it already driving like that.  So there's no telling how long it actually has been driving like this.  Hopefully damage is too bad when we drop the pan.   I am having a hard time finding a site that sells the solenoid for the 5 speed auto, do you have any suggestions?
    • That'll be most likely down the road...  LOL  
    • a stock / option or aftermarket?
×
×
  • Create New...