Jump to content
SAU Community

Recommended Posts

When i accelerate at the green lights after coming to a stop, people around me are always going faster then me and so i compared my rpm to their rpm when accelerating from the green light is they often always rev up to 3300 rpm as this is what it takes for my R34 to keep up with them side by side

I usually rev up and cruise after the start of green lights constantly at 1500 - 2000 rpm because anymore then that my engine feels like its wearing itself out and burning unnecessary fuel as my engine always gives off this whooshing sound after 3000 rpm and roars loudly within the car's cabin. (oh and i usually smell fuel within the car after revving it up to 3000)

Whats weird is that i tested beside cars such as old camrys, corollas, Mazda 3s and 8 etc and they are driven by mature aged people and they drive hard up to 3300 rpm usually.

Yet even after revving it up to 3300 rpm cars behind me still stick close expecting me to go faster even when i'm on the left side of the road.

Oh and i forgot to add, i rev to 2500 rpm and constantly stay there gets me to 40 - 50 km slowly and i mean very slowly like around 6 seconds and that every car overtook me like i'm driving like a grandma.

Edited by Elegant Skyline

Seriously

the engine is most efficient at 7000rpm , so that's where you need to be all the time.

Its why the R34s have tiptronic, you can manually select the gear to get you closest to 7000rpm

When i use my tiptronic i often smell something burning so i don't use it plus i don't want to go over 3000 rpm as it seems too much for me.

Fuel needle drops like a rock when i reach near it.

Even then i stick to the speed limit and keep getting bad fuel economy.

Most efficient?

So i would use up to nearly half my fuel tank just to go the city and back at Liverpool?

I wonder if any tuning will give me better acceleration below the 2500 rpm range but be economical.

22's = more efficient tyres. Just ask the tyre joint for some.

Sounds like you need to remove the stupid mods and get someone to look at the car. Have you checked for boost leaks?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hows your intake piping? Are you still running stock? Having in the stock AFM position would mean, if the BOV was shut/venting out, it'd create the almost stalling kind of effect right // "the rich pulse behaviour" due to MAF thinking air is flowing ? But this would be better than having the bov in the stock position + MAF on/just before cross over piping right?
    • Essentially, yes. Although I wouldn't put the AFM on the crossover pipe. I'd want to put it into what amounts to the correct size tube, which is more easily done in the intercooler pipework. I bought a mount tube for card stile AFM that replaces the stock AFM - although being a cheap AliExpress knockoff, it had not flange and I had to make and weld my own. But it is the same length and diameter as the stock RB AFM, goes on my airbox, etc etc. I don't have a sick enough rig to warrant anything different, and the swap will take 5 minutes (when I finally get around to it and the injectors & the dyno tune).
    • So to summarise, the best thing to do is to move recirc to between turbo and IC, and maf on the crossover pipe. Meaning I'd need a recirc flange, drill a hole in the piping on turbo outlet area. And drill hole on crossover to fit/weld maf sensor? Either that or put the MAF on the turbo inlet right?  Is an aftermarket recirc/blowoff valve recommended? Do currently have family in Japan so could probably bring something back with maybe a cheeky lil SuperAutobacs run?
    • Yep, so far most have said that it looks like corrosion on the wall from piston not moving. Which then has probably damaged the oil rings and caused those vertical marks. The longest the engine was still after the rebuild, was the winter of 2018 - 2019, plus the boat trip to Japan. When I shipped the car, it had normal gas in the tank but before that winter pause, it had E85 in tank.  In any case, even if either one of those was the cause, it happened close to 6 years ago and the car has been driven something like 30 000kms after the fact. Again, apart from the plugs and the dip stick, there is nothing in the way the car runs that would indicate what has been going on in the engine. I am going to consult a shop and ask their opinion, what would be the best approach. I do have some access to a garage I could use to diagnose further myself, but time is very restrictive. Might end up buying another engine that could be used while this one is being remedied. Without pulling the head, it will be impossible to find out if it needs another bore, but here's to hoping a hone would suffice.  Goddamnit, I would really have preferred this not happening.  
    • Boot is going to be replaced eventually. I just wire brushed what I could and rust converted. Then painted in rust kill primer. the spoiler also got repainted and plugs replaced on the ends. The under side of the bonnet is going to be black also, currently white. But red on the top side, same colour code as the silo to begin.
×
×
  • Create New...