Jump to content
SAU Community

V35 250Gt Issue - Please Help

Richy08

By Richy08,
in Western Australia

 Share

Recommended Posts

Richy08 Collaborator

Richy08

Posted
Posted

Hello Guys,

I've been having this problem with my V35 250GT for some over 6 months now and the car is now sitting at a well known workshop where the mechanics are stuck so I've come to the forum to ask for assistance.

6 months ago I had my VQ25DE engine replaced with a new one, since then the car has had issues on full throttle and the mechanic who installed the engine closed up his shop.
I took the vehicle into Nissan and they said that there was a TPS Error code being thrown up on their diagnostics tool, they checked the TPS and saw the wiring had been hacked so they tried to fix it up.

This solved the problem for about a month and then the car started to feel almost like it hits a rev limiter on full throttle and the whole car shakes, it drives fine if you lightly accelerate all the way up the rev ranges.

I've been battling with the issue for a few months because nobody knew the answer to the problem, until a few days ago when the vehicle does the same on about 2,000 RPM's now and is practiaclly undriveable.

Another scan has thrown up a curl valve error (apparently sits at the front of the engine to open and close throttle) but again, the mechanic is not 100% sure without another V35 side by side to replace parts and test.

If anyone can help, please help as I am stuck and left with no other options. Even if someone can lend HyperDrive in Malaga their V35 250GT for a cost so that they can test replacement parts I will be forever thankful.

Cheers Guys!

Link to comment
https://www.sau.com.au/forums/topic/440166-v35-250gt-issue-please-help/
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PotatoCake
      Exhaust silencers/varex exhausts

      By PotatoCake · Posted

      I’m also conscious that e85 is slowly being phased out. Not all United’s have them anymore. Can’t take the risk of being low on petrol and assuming the servo will have it. 
    • The Bogan
      NC MX5

      By The Bogan · Posted

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      MR HAMMER has said his piece. Painted up to avoid Rusty Rusty. Actually lines up well. (i.e it lines up the same as the unmolested GTR guard). Turns out the GTR Strut brace does foul on the bonnet vents ever so slightly. May need a little bendy bendy if intended to keep using with a strut brace. So spacing it out to clear the FAST102 is not an option. Annoyingly, the bonnet vents also foul on the heater lines running over the engine. Given this engine does not EVER require a heater, a delete loop is going to be used. Don't worry, the defogger uses the AC. The heater is basically "Do not use the aircon and turn the fan on". It will still be effective, I promise.... once I get the system regassed... Will have to revisit with unvented bonnet I suppose, and suitable strut brace. There's plans to do this and other things tonight and bleed brakes (there was a weep) and put the bumper back on, and take Good Friday morning - Because troubleshooting on the side of the road limping it home at midnight tonight is ... not very smart.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      Thank you all for you assistance. I contacted Nistune regarding the support for the RB20DE along with my ECU Code (23710-10U00). They do have a map for it and added the RB20DE as a purchasable option now as well. They also added Malta as a Billing and Delivery options as this was missing. I was honestly amazed at their quick response and action, it took less than 24 hours. I also looked again at direct fit options for injectors, just in case I were to replace them. DeatschWerks seem to use a Bosch EV14 base and makes ones that fit mine at 440cc lowest, but also have 550cc at the same price. I tried looking for other direct fit options and managed to find one (also Bosch EV14 based) which includes a plug and play adapter on ebay. Did a small test with a Noid Light on the troubled injectors and all seems good, so they are pulsing properly electrically. One weird part is that they are missing on the same two cylinders as before I got the injectors cleaned. Mechanic also found this weird as he did not label the injectors and it is unlikely to have the faulty injectors be installed in the same cylinders.  
    • Murray_Calavera
      Exhaust silencers/varex exhausts

      By Murray_Calavera · Posted

      Nice, let me know how you find the 98 tune
×
×
  • Create New...