Jump to content
SAU Community

Recommended Posts

Hi guys

I am putting a set of HPI dumps onto my RB26 (76.3mm outlet from memory) and have a Tomei Ti exhaust (90mm) from the cat back.

I'm trying to find a suitable set of front pipes that will match those sizes, and the only ones I can find are:

Pentroof:

http://www.nengun.com/pentroof/large-diameter-front-pipe

Midori:

http://www.nengun.com/midori-seibi/titanium-gtr-front-pipe

The thing is, I would prefer tuned length if at all possible - are these tuned length?

If not, is there anything else that would be suitable that is tuned length and matches my 76.3mm dumps and 90mm exhaust?

Cheers!

as scotty said it's not a manifold so just plumb it up as it fits. You're best bet is going custom but you might get lucky with an off the shelf part

Edited by Blackkers

I had the same setup, ended up getting some custom twin 76mm to 90mm front pipes as I couldn't find any off the shelf that size

Cheers Michael, have decided against the two I posted and will look for a custom job as well

Scott and Tim, sorry I'm lost on what you're talking about - I think you've misread my question - I'm not looking for advice on tuned-length vs non-tuned length pipes; thanks for the input anyway.

Edited by PSIKO

Well then you should pay $1500 to $2000 for those "Tuned length' pipes shipped from Japan and not ask our opinion. It's not like I know what I am talking about anyway...

I could make better pipes than those for under $500 in stainless, and they wouldn't drag on every speed hump you drive over.

Well then you should pay $1500 to $2000 for those "Tuned length' pipes shipped from Japan and not ask our opinion. It's not like I know what I am talking about anyway...

I could make better pipes than those for under $500 in stainless, and they wouldn't drag on every speed hump you drive over.

So it's tuned length vs tuned design!

Well then you should pay $1500 to $2000 for those "Tuned length' pipes shipped from Japan and not ask our opinion. It's not like I know what I am talking about anyway...

I could make better pipes than those for under $500 in stainless, and they wouldn't drag on every speed hump you drive over.

I missed the bit where the OP asked for opinions. I assume he wants tuned length because they sound so much nicer than non-tuned front pipes.

Do you have any examples of your front pipes out of interest Scotty? I could only see these pieces of art in this build thread. The turbo elbow particularly caught my attention.

http://www.skylinesaustralia.com/forums/topic/419605-my-r34-gt-t-streettrack-builddiary/page-11?hl=+scotty

Edited by colinhunt
  • Like 1

Do you have any examples of your front pipes out of interest Scotty?

I don't, mainly as I have never been asked to make them. Typically most GTR owners want 'brand name' parts I have found.

I assume Tony's outlet pipe looked a little 'wrong' to you, it was the only way a turbo that large would fit behind the PS pump without hitting the strut tower. A close up of the exterior of the pipe is interesting, but the inside was perfectly smooth, and it flowed the numbers... Again, not something a GTR owner would generally go for, it's not shiny enough, no matter how practical it is.

I don't, mainly as I have never been asked to make them. Typically most GTR owners want 'brand name' parts I have found.

I assume Tony's outlet pipe looked a little 'wrong' to you, it was the only way a turbo that large would fit behind the PS pump without hitting the strut tower. A close up of the exterior of the pipe is interesting, but the inside was perfectly smooth, and it flowed the numbers... Again, not something a GTR owner would generally go for, it's not shiny enough, no matter how practical it is.

Most of the jap stuff is junk. Exhausts, catch cans, most fuel rails are junk designs. Aussie engineering could take it to the jap "bling" companies without batting an eyelid. Catalogue shopping is junk.

  • 10 months later...

Most of the jap stuff is junk. Exhausts, catch cans, most fuel rails are junk designs. Aussie engineering could take it to the jap "bling" companies without batting an eyelid. Catalogue shopping is junk.

Bit late but your talking out of your piggaz

Bit late but your talking out of your piggaz

I think you need to ask the japs what they thought of our Aussie Godzillas before making that remark.

Maybe ask them what they had been taught from us......

Bit late but your talking out of your piggaz

Am I?

You bumped a 12 month old thread to tell me I'm an idiot! :/

The point I was trying to make is that you can't just flick through a trust/Nismo/HKS/whatever and pick parts and expect some awesome result.

An example. A SARD fuel rail. Looks pretty, duel entry single out. Sounds sweet yeah? The bloody piece of shit doesn't have a seat for the injectors to push up against. Waste of time.

Kakimoto Full Mega N1 exhaust. Looks mad with it's bit tough cannon. Has some 2 inch restrictor/"silencer"/taper down/whatever you want to call it in the rear muffler. You're so called "90 mm exhaust" now because a 50. Waste of farken time.

Tomei Expreme RB 26 stainless manifolds. Cost a fortune, look pretty. Made from shit stainless that crack and also offer no performance advantage. I've personally done a back to back. A mate has a Evo Tomei manifold sitting on his garage floor because they're cracked. Make a good paperweight though!

Two quick examples that quickly came to my head.

Have fun with your catalogues, mate!

  • Like 1

His name says it all Piggy don't worry son! :)

Your cars results speak for themselves and i think the only Jap parts you have on it are the cooler and intake manifold?

Edited by Mick_o

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I like it when the counter chick leads you out the back into the racks and says "have a grub around in here and see if you can find what you need. I'll be back in a few minutes. Just left me in front of a massive motorised shelving system and 2-3 million fasteners, so I could find a peculiar SS shoulder bolt with cap head. Gotta love country towns.
    • I used this https://osgiken.com.au/product/os-giken-os-250r-lsd-gear-oil-80w250-1-litre/   shut my nismo 1.5 pro up by heaps…. Not silent though. Gives the car character and personality. It ain’t a carolla. If you want silent, put a quaife in it.
    • It's about the same time for me from Bunnings, or the Fasteners. My big push away from takeaway food, and gluten in general keeps me away from the Bunnings Snags too! Weather up here, I've been out for two walks today in the beautiful sunshine. Had a few little drizzles, and some wind, that honestly, a tin of beans and I could compete on how harsh she blows Thankfully, being this bit inland, we're not getting anything much really. Will probably pick up a bit more when/if Cyclone Alfie decides to come ashore. A few areas in the GC though, and south into NSW are really getting smashed though! Right now, I'm just annoyed Alfie hasn't hit, as I'm not allowed to crack into the BBQ foods like the bacon and eggs until the Cyclone hits "In case we lose power"...
    • I love fastener joints, the price difference between them and joints like Bunnings or Super Cheap is amazing, and they either have exactly what you want, or they can get it to quick They have even given me some for free when I only needed a couple of specific size In saying this, I have paid premium for fasteners from Bunnings if they have the sizes I need, but only for convenience really, as my local is only 10 minutes away, the Sushi joint near them is also a consideration  How's the weather Matt? Stay safe mate
    • Wideband is worth setting up if only for tuning purposes. I would not mess with the ignition system unless there's a misfire. HKS crank trigger is popular out here for the relatively easily sourced Denso crank sensor, not a bad idea to install as well regardless of power level on a standalone. Boost leak test is worth thinking about. Oil pressure sensor tied to a fuel cut isn't a bad idea either. Getting the tune figured out is a good idea. Without putting eyes on it and getting under it there's no way for us to tell you exactly what it needs but most likely you're down to the last 10% that will make a big, big difference in how happy you are with the car.
×
×
  • Create New...