Jump to content
SAU Community

Recommended Posts

So this is what my car looked like the day I bought it, complete with Dolphin body kit :)

20130802_153523_zpsd9a3c3d2.jpg

Yep nice and clean, note the ACT plates (you guys have lovely roads).

Well this was very short-lived, after introducing the Stagea to the 'fantastic' roads we have to offer in NSW it wasn't long until it was copping a few bumps and scrapes.

Then one dark night a chopped up drum of some kind was left in the middle of the road in an 80km/h zone which fatefully met with my front bumper causing much damage and distress.

IMAG0231_zps1341c80d.jpg

It wasn't a good look, but I didn't want to spend the time and money fixing it with the thought that somewhere down the track it might happen again.

IMAG0196_zpsf3d14902.jpg

So I thought why not clean it up and create a custom front bumper! I was forced to drive around for about a week without a front bumper since I was having problems with my forester... and somehow escaping the glares of about 6 cop cars we made it without incident and re-attached the bumper today!

IMAG0229_zpse25c6f36.jpg

I've grown fond of the look (although my black FM Intercooler is now a bit visible), what does SAU think?

Link to comment
https://www.sau.com.au/forums/topic/441448-accidental-custom-front-bumper/
Share on other sites

my first thought was thats sucks, id be pissed if that happened to my car!!!
second thought, you can now cruise round vl calais style...

personally im not a huge fan of it, i dont hate it though.... but end of the day, if you like it then its all good :D

Edited by MatthewT85

IMAG0231_zps1341c80d.jpg

Your look is hilarious.

Your intercooler should have the same kind of sad face too; as the amount of air that will now completely avoid going through the core is quite surprising.

If I were you I'd be saving for a new bar.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...