Jump to content
SAU Community

Help Needed, R32 Wont Start

Strick.
 Share

Recommended Posts

Strick. Rising Star

Strick.

Posted
Posted

Gday everyone,

new to skylines and RB25s, ive just pulled my R32 GTS-T out of the shed to start working on her finally. It has an RB25 and is manual.

Car wont start. Started no worries before i last touched it, about 4 months ago (has been on trickle charge the whole time. Have put 5 litres of fresh 98 in. Turn the key, has the starting sound however motor wont turn over. Has about 13 volts in the battery.

Havent tryed a push start yet as im by myself.

Where do i start?

Any help would be great.

thanks

Link to comment
https://www.sau.com.au/forums/topic/442166-help-needed-r32-wont-start/
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

You mean it turns over (starter motor works) but won't start?

The injectors may have gummed up and aren't opening. Get them cleaned.

Check for fuel (fuel pump, fuel filter), spark and compression. Might need a few more than 5 litres of fuel in the tank too!

Strick. Rising Star

Strick.

Posted
  • Author
Posted

Thanks for the help guys. Im pulling it apart now to check all that. I think ill get the injectors cleaned while i have them out.

The plugs were black as all buggery too so that cant be helping!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 gtt rb25det neo timing belt kit

      By GTSBoy · Posted

      Nissan/Pitwork is fine stuff. HKS is just marketing wank. I personally wouldn't do the idler if it is already new. If it looks and feels fine, it is fine. But as D says - it's cheap to add it to the job. The water pump ditto. Even more so. If it show no signs of problems, then it is nearly new - leave it.
    • Duncan
      R34 gtt rb25det neo timing belt kit

      By Duncan · Posted

      1. I can't see a location on your profile but you do mention GBP so I'll assume you are in UK. In Australia, CBC make a timing belt kit with the gears and idler and tension bearing and that is what I use without any problems. I'm sure OEM or HKS are also fine but I wouldn't pay extra for HKS over anything else. 2. Yes, I would always change the idler and tensioner and the stud and bolt that hold them in. Assuming they were all done last time it is highly unlikely you would have a problem, but they are very cheap to add to the job considering the time it will take anyway.  3. No, you don't need to lock them as such (I think that is more for engines without timing marks), but you should make sure they move as little as possible once the belt is off as you can hit pistons on valves if they move too far. As always, make sure you line it all up to top dead centre with the timing marks aligned before you take the old belt off.
    • The Bogan
      Boxes of oil?

      By The Bogan · Posted

    • MBS206
      Boxes of oil?

      By MBS206 · Posted

      How to wreak havoc at a bogans party... Swap out the goon bag hanging from the clothes line with oil bag... Watch chaos ensue during Goon of Fortune....
    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      Hey everyone,   I’m looking for some advice on replacing the timing belt on my RB25DET Neo-powered 1998 Skyline. The engine was fully built about five years ago, including a fresh timing belt, water pump, and other essentials. However, since then, the car has only covered around 2,000–3,000 miles. It’s currently making around 650hp.   Even though the mileage is low, I know timing belts have a time-based lifespan too, and most recommendations suggest changing them every five to six years or 50,000 miles. Since I’m at that time mark, I’d rather not take any risks and plan to swap it out soon.   A few things I’d like to hear opinions on: 1. What’s the best belt for this setup? Should I go with an OEM Nissan belt, or is the HKS fine-tune a better choice given the power level? 2. Would you bother replacing the idler pulley and tensioner at the same time, or only if they show wear? 3. When swapping the belt, is it necessary to lock the cam and crank gears in place, or is lining up the timing marks enough? I’ve seen different approaches, and I want to make sure I do it right.   The water pump was changed with the rebuild and isn’t run off the timing belt, so I don’t see a need to replace it again. I just want to make sure I approach this the right way.   Any insight would be much appreciated. Thanks!
×
×
  • Create New...