Jump to content
SAU Community

Recommended Posts

Hi all,

Over the past week I've noticed a burning smell coming from my car. Started off as just the smell but today after pulling into the driveway I saw a bit of smoke coming from the engine (couldn't see where from specifically). Smells like either burning oil or burning clutch. Any thoughts? The only thing that has changed recently is I've been driving around without the engine under tray on (didn't get around to putting it on after the last oil change about 2 weeks ago), could that cause a problem, or cause me to notice a problem?

There is also some kind of leak coming from the drivers side front corner (near the coolant reservoir) that has been there for ages (can only tell cause the tray is dirty at that point). Not sure what it is but never seem to lose coolant so I'm guessing it's not that.

Any thoughts anyone?

Any help would be GREATLY appreciated!

Thanks,

Link to comment
https://www.sau.com.au/forums/topic/442225-m35-burning-smell-and-smoke/
Share on other sites

Most common issue with burning oil smell is the cam covers leaking onto manifolds, and in particular around the turbo area.

Have a look for smoke / oily dampness round the rear of the engine bay passenger side.

will be fixed by replacing the seal around the cover.

Most common issue with burning oil smell is the cam covers leaking onto manifolds, and in particular around the turbo area.

Have a look for smoke / oily dampness round the rear of the engine bay passenger side.

will be fixed by replacing the seal around the cover.

Thanks for the advice. Had a look around the rear and it actually looks surprisingly dry and clean (unless I'm looking in the wrong spot). However the front and half way down the side is fairly covered in oil. Could this be the same problem? See image attached. Any thoughts would be really helpful, don't wanna be driving it if I'm causing more damage.

It has always had a bit of an oil leak somewhere as the oil level drops by a litre or two by the time I get to the 5000-7000km oil change

post-105237-13982581140452_thumb.jpg

The passenger rocker cover seal goes hard due to the turbo heat, it weeps down onto the turbo causing an oil smell when you put the heater on.

As the gasket seal is only $25 I would just change it, well known problem. It will take you a while to change it the first time, the plenum needs to come off.

Part No: 13270-AL612

Thanks guys, appreciate it. After having a sniff this morning it does smell like it's coming from the area you are describing so I guess I'll give it a go. There isn't any how to for this is there haha? Is it a job someone with limited mechanical experience could tackle?

Just make sure the gasket doesn't fall out of it's groove as you slide it under the heater line, check with a mirror or small screwdriver before tightening the cover bolts.

add a little gasket goo so it sticks in the seam and less chance off falling out as that heater hose is a p@ick to navigate

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That is correct. I'm using a modified ABS ring and a ZF speed sensor on my rear diff for speed input. I'm running a Haltech ecu. 
    • Been busy with the newborn. We originally thought we were going to go for a third, but we're good with two lol. He's starting to actually sleep now so I've had some energy to work on the car. It's been parked away in the garage since late November due to winter.  I went ahead and redid all my head oil drains. I originally had my front and rear head drain going into the same pipe but have since split them up. I also added an Ethanol content sensor to get ready to run E85 this summer. Tossed it on my return line. Sensor sits nicely under my intake manifold.    I also have a lot of parts that came in for my rear end. I'll be swapping over to a 3.3 final drive and doing the GK teck anti squat mod. While the rear subframe is off, I'll also change every bushing. We're planning on buying another house soon with the condition that I get at a minimum a 2 door garage, so I'll wait to have more room for this. Now onto the strange things that recently happened... After changing the lower rad hose (It had been sitting in my cabinet for well over a year and was the last hose I had to replace), I let the car idle in the garage to bleed my coolant. After running for a few minutes, it started missing. Got much worst within a minute or two and then stalled and would not restart. My crank sensor decided to crap itself. No damage, no explanation, just died. I went ahead and replaced it with another ZF sensor but the heavier duty stainless model with a shield. Tossed that in and started right up. Has anyone else seen this? I hate when things fail without cause. Luckily this was a blessing in disguise... This lead me to recheck my timing. It seems I may have had a beer or two the last time I had set my TDC angle as I was off exactly 5 degrees... I miscounted a line haha. I was running 5 degrees less then commanded. It's a little embarrassing but helps explain why my dyno operator seemed to think I should be making more then 478rwkws.        
    • Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
×
×
  • Create New...